[NSRCA-discussion] Embarrassing Programming Problem - Inventingthe wheel...

[Pete Cosky]

I knew I liked Ron for a reason......great invention.

----- Original Message ----- 
From: "Ron Van Putte" <vanputte at cox.net>
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, May 06, 2008 2:22 PM
Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem - 
Inventingthe wheel...


> Yeah.  I had more hair then.
>
> Ron
>
> On May 6, 2008, at 1:08 PM, Mark Atwood wrote:
>
>> For those that want to see Ron in his younger days...  A reenactment.
>>
>> http://www.youtube.com/watch?v=oTLy6EBmd5s
>>
>>
>> On 5/6/08 1:57 PM, "george w. kennie" <geobet at gis.net> wrote:
>>
>>> I remember !   What a tough time we had sanding those corners
>>> down. If only
>>> we had thought to balance them.
>>> G.
>>>
>>>
>>>
>>> ----- Original Message -----
>>> From: "Ron Van Putte" <vanputte at cox.net>
>>> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
>>> Sent: Monday, May 05, 2008 4:55 PM
>>> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem
>>>
>>>
>>>> I was not around when the wheel was first invented.  However, I
>>>> participated in the first post production design iteration:  Making
>>>> them round to get rid of the "clunk, clunk, clunk".
>>>>
>>>> Ron
>>>>
>>>> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:
>>>>
>>>>> Because he was around when it was invented the first time???
>>>>>
>>>>>  :):):):)
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> On 5/5/08 4:20 PM, "Tony" <tony at radiosouthrc.com> wrote:
>>>>>
>>>>>> Ron:
>>>>>> Why are you re-inventing the wheel?
>>>>>> Use the Ailvator pre-set mix for dual elevator servos already
>>>>>> built into the
>>>>>> 9Z..
>>>>>>
>>>>>>
>>>>>> Tony Stillman, President
>>>>>> Radio South, Inc.
>>>>>> 139 Altama Connector, Box 322
>>>>>> Brunswick, GA  31525
>>>>>> 1-800-962-7802
>>>>>> www.radiosouthrc.com
>>>>>>
>>>>>> -----Original Message-----
>>>>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>>>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
>>>>>> Van Putte
>>>>>> Sent: Monday, May 05, 2008 4:09 PM
>>>>>> To: General pattern discussion
>>>>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
>>>>>>
>>>>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and
>>>>>> using
>>>>>> channels 2 and 6 for servos on each elevator half.  I have PMX set
>>>>>> for channels 2 and 6, mixing channel 2 into channel 6 and
>>>>>> everything
>>>>>> works fine, except the servo on channel 6 only moves about 2/3 the
>>>>>> throw of the servo on channel 2.  I've tried everything I can
>>>>>> think
>>>>>> of to rectify the problem with no success.  In addition, there's a
>>>>>> small shift in neutral when going from high rate elevator to low
>>>>>> rate.
>>>>>>
>>>>>> I started with an unused model in the menu, so I don't think
>>>>>> there's
>>>>>> any hidden programming lurking.
>>>>>>
>>>>>> Any ideas?  I'll be very irritated to find there's a simple
>>>>>> solution,
>>>>>> but I'd also be very grateful to have the problem go away.
>>>>>>
>>>>>> Ron Van Putte
>>>>>> _______________________________________________
>>>>>> NSRCA-discussion mailing list
>>>>>> NSRCA-discussion at lists.nsrca.org
>>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>>
>>>>>> _______________________________________________
>>>>>> NSRCA-discussion mailing list
>>>>>> NSRCA-discussion at lists.nsrca.org
>>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>
>>>>> _______________________________________________
>>>>> NSRCA-discussion mailing list
>>>>> NSRCA-discussion at lists.nsrca.org
>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>
>>>
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>