[NSRCA-discussion] Embarrassing Programming Problem - Inventing the wheel...

[Ron Van Putte]

Yeah.  I had more hair then.

Ron

On May 6, 2008, at 1:08 PM, Mark Atwood wrote:

> For those that want to see Ron in his younger days...  A reenactment.
>
> http://www.youtube.com/watch?v=oTLy6EBmd5s
>
>
> On 5/6/08 1:57 PM, "george w. kennie" <geobet at gis.net> wrote:
>
>> I remember !   What a tough time we had sanding those corners  
>> down. If only
>> we had thought to balance them.
>> G.
>>
>>
>>
>> ----- Original Message -----
>> From: "Ron Van Putte" <vanputte at cox.net>
>> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
>> Sent: Monday, May 05, 2008 4:55 PM
>> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem
>>
>>
>>> I was not around when the wheel was first invented.  However, I
>>> participated in the first post production design iteration:  Making
>>> them round to get rid of the "clunk, clunk, clunk".
>>>
>>> Ron
>>>
>>> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:
>>>
>>>> Because he was around when it was invented the first time???
>>>>
>>>>  :):):):)
>>>>
>>>>
>>>>
>>>>
>>>> On 5/5/08 4:20 PM, "Tony" <tony at radiosouthrc.com> wrote:
>>>>
>>>>> Ron:
>>>>> Why are you re-inventing the wheel?
>>>>> Use the Ailvator pre-set mix for dual elevator servos already
>>>>> built into the
>>>>> 9Z..
>>>>>
>>>>>
>>>>> Tony Stillman, President
>>>>> Radio South, Inc.
>>>>> 139 Altama Connector, Box 322
>>>>> Brunswick, GA  31525
>>>>> 1-800-962-7802
>>>>> www.radiosouthrc.com
>>>>>
>>>>> -----Original Message-----
>>>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
>>>>> Van Putte
>>>>> Sent: Monday, May 05, 2008 4:09 PM
>>>>> To: General pattern discussion
>>>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
>>>>>
>>>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and  
>>>>> using
>>>>> channels 2 and 6 for servos on each elevator half.  I have PMX set
>>>>> for channels 2 and 6, mixing channel 2 into channel 6 and  
>>>>> everything
>>>>> works fine, except the servo on channel 6 only moves about 2/3 the
>>>>> throw of the servo on channel 2.  I've tried everything I can  
>>>>> think
>>>>> of to rectify the problem with no success.  In addition, there's a
>>>>> small shift in neutral when going from high rate elevator to low
>>>>> rate.
>>>>>
>>>>> I started with an unused model in the menu, so I don't think  
>>>>> there's
>>>>> any hidden programming lurking.
>>>>>
>>>>> Any ideas?  I'll be very irritated to find there's a simple  
>>>>> solution,
>>>>> but I'd also be very grateful to have the problem go away.
>>>>>
>>>>> Ron Van Putte
>>>>> _______________________________________________
>>>>> NSRCA-discussion mailing list
>>>>> NSRCA-discussion at lists.nsrca.org
>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>
>>>>> _______________________________________________
>>>>> NSRCA-discussion mailing list
>>>>> NSRCA-discussion at lists.nsrca.org
>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion