[NSRCA-discussion] Embarrassing Programming Problem -Inventingthe wheel...

[Del Rykert]

So did Ron invent that pole dancing at end of klip also ?

    Del

----- Original Message ----- 
From: "Pete Cosky" <pcosky at comcast.net>
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, May 06, 2008 2:32 PM
Subject: Re: [NSRCA-discussion] Embarrassing Programming 
Problem -Inventingthe wheel...


>I knew I liked Ron for a reason......great invention.
>
> ----- Original Message ----- 
> From: "Ron Van Putte" <vanputte at cox.net>
> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
> Sent: Tuesday, May 06, 2008 2:22 PM
> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem -
> Inventingthe wheel...
>
>
>> Yeah.  I had more hair then.
>>
>> Ron
>>
>> On May 6, 2008, at 1:08 PM, Mark Atwood wrote:
>>
>>> For those that want to see Ron in his younger days...  A reenactment.
>>>
>>> http://www.youtube.com/watch?v=oTLy6EBmd5s
>>>
>>>
>>> On 5/6/08 1:57 PM, "george w. kennie" <geobet at gis.net> wrote:
>>>
>>>> I remember !   What a tough time we had sanding those corners
>>>> down. If only
>>>> we had thought to balance them.
>>>> G.
>>>>
>>>>
>>>>
>>>> ----- Original Message -----
>>>> From: "Ron Van Putte" <vanputte at cox.net>
>>>> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
>>>> Sent: Monday, May 05, 2008 4:55 PM
>>>> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem
>>>>
>>>>
>>>>> I was not around when the wheel was first invented.  However, I
>>>>> participated in the first post production design iteration:  Making
>>>>> them round to get rid of the "clunk, clunk, clunk".
>>>>>
>>>>> Ron
>>>>>
>>>>> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:
>>>>>
>>>>>> Because he was around when it was invented the first time???
>>>>>>
>>>>>>  :):):):)
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> On 5/5/08 4:20 PM, "Tony" <tony at radiosouthrc.com> wrote:
>>>>>>
>>>>>>> Ron:
>>>>>>> Why are you re-inventing the wheel?
>>>>>>> Use the Ailvator pre-set mix for dual elevator servos already
>>>>>>> built into the
>>>>>>> 9Z..
>>>>>>>
>>>>>>>
>>>>>>> Tony Stillman, President
>>>>>>> Radio South, Inc.
>>>>>>> 139 Altama Connector, Box 322
>>>>>>> Brunswick, GA  31525
>>>>>>> 1-800-962-7802
>>>>>>> www.radiosouthrc.com
>>>>>>>
>>>>>>> -----Original Message-----
>>>>>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>>>>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
>>>>>>> Van Putte
>>>>>>> Sent: Monday, May 05, 2008 4:09 PM
>>>>>>> To: General pattern discussion
>>>>>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
>>>>>>>
>>>>>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and
>>>>>>> using
>>>>>>> channels 2 and 6 for servos on each elevator half.  I have PMX set
>>>>>>> for channels 2 and 6, mixing channel 2 into channel 6 and
>>>>>>> everything
>>>>>>> works fine, except the servo on channel 6 only moves about 2/3 the
>>>>>>> throw of the servo on channel 2.  I've tried everything I can
>>>>>>> think
>>>>>>> of to rectify the problem with no success.  In addition, there's a
>>>>>>> small shift in neutral when going from high rate elevator to low
>>>>>>> rate.
>>>>>>>
>>>>>>> I started with an unused model in the menu, so I don't think
>>>>>>> there's
>>>>>>> any hidden programming lurking.
>>>>>>>
>>>>>>> Any ideas?  I'll be very irritated to find there's a simple
>>>>>>> solution,
>>>>>>> but I'd also be very grateful to have the problem go away.
>>>>>>>
>>>>>>> Ron Van Putte
>>>>>>> _______________________________________________
>>>>>>> NSRCA-discussion mailing list
>>>>>>> NSRCA-discussion at lists.nsrca.org
>>>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> NSRCA-discussion mailing list
>>>>>>> NSRCA-discussion at lists.nsrca.org
>>>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>>
>>>>>> _______________________________________________
>>>>>> NSRCA-discussion mailing list
>>>>>> NSRCA-discussion at lists.nsrca.org
>>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>
>>>>> _______________________________________________
>>>>> NSRCA-discussion mailing list
>>>>> NSRCA-discussion at lists.nsrca.org
>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>
>>>>
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>