[NSRCA-discussion] Embarrassing Programming Problem

[Ron Van Putte]

Haven't tried that.

Ron

On May 5, 2008, at 5:22 PM, Duane Beck wrote:

> Do you get the same shift if you reset the subtrims to 0 (make note  
> of the original values first)?
>
> Duane
>
> -------------- Original message --------------
> From: Ron Van Putte <vanputte at cox.net>
>
> > OK. I caved and went with ailevator. I nulled out the aileron
> > inputs and everything works as it should, EXCEPT I'm still getting a
> > small neutral shift on both elevators (same direction) when moving
> > the elevator dual rate switch.
> >
> > Ron
> >
> > On May 5, 2008, at 3:20 PM, Tony wrote:
> >
> > > Ron:
> > > Why are you re-inventing the wheel?
> > > Use the Ailvator pre-set mix for dual elevator servos already  
> built
> > > into the
> > > 9Z..
> > >
> > >
> > > Tony Stillman, President
> > > Radio South, Inc.
> > > 139 Altama Connector, Box 322
> > > Brunswick, GA 31525
> > > 1-800-962-7802
> > > www.radiosouthrc.com
> > >
> &g t; > -----Original Message-----
> > > From: nsrca-discussion-bounces at lists.nsrca.org
> > > [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
> > > Van Putte
> > > Sent: Monday, May 05, 2008 4:09 PM
> > > To: General pattern discussion
> > > Subject: [NSRCA-discussion] Embarrassing Programming Problem
> > >
> > > I'm setting up a new airplane on my Futaba 9ZAP transmitter and  
> using
> > > channels 2 and 6 for servos on each elevator half. I have PMX set
> > > for channels 2 and 6, mixing channel 2 into channel 6 and  
> everything
> > > works fine, except the servo on channel 6 only moves about 2/3 the
> > > throw of the servo on channel 2. I've tried everything I can think
> > > of to rectify the problem with no success. In addition, there's a
> > > small shift in neutral when going from high rate elevator to  
> low rate.
> > >
> > > I st arted with an unused model in the menu, so I don't think  
> there's
> > > any hidden programming lurking.
> > >
> > > Any ideas? I'll be very irritated to find there's a simple  
> solution,
> > > but I'd also be very grateful to have the problem go away.
> > >
> > > Ron Van Putte
> > > _______________________________________________
> > > NSRCA-discussion mailing list
> > > NSRCA-discussion at lists.nsrca.org
> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> > >
> > > _______________________________________________
> > > NSRCA-discussion mailing list
> > > NSRCA-discussion at lists.nsrca.org
> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussio n
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion