[NSRCA-discussion] Embarrassing Programming Problem

[vicenterc at comcast.net]

Both were assembled around 4 PM for beer on Friday....

--
Vicente "Vince" Bortone

-------------- Original message -------------- 
From: Ron Van Putte <vanputte at cox.net> 

> I might agree, but it does the same thing with two 9Z transmitters. 
> I wonder what the odds are that two transmitters have the same problem. 
> 
> Ron 
> 
> On May 5, 2008, at 5:15 PM, vicenterc at comcast.net wrote: 
> 
> > Ron, 
> > 
> > I believe that you need to send the radio to Tony for pots 
> > adjustment. If the radio is new send it back to Futaba. 
> > 
> > -- 
> > Vicente "Vince" Bortone 
> > 
> > -------------- Original message -------------- 
> > From: Ron Van Putte 
> > 
> > > OK. I caved and went with ailevator. I nulled out the aileron 
> > > inputs and everything works as it should, EXCEPT I'm still getting a 
> > > small neutral shift on both elevators (same direction) when moving 
> > > the elevator dual rate switch. 
> > > 
> > > Ron 
> > > 
> > > On May 5, 2008, at 3:20 PM, Tony wrote: 
> > > 
> > > > Ron: 
> > > > Why are you re-inventing the wheel? 
> > > > Use the Ailvator pre-set mix for dual elevator servos already 
> > built 
> > > > into the 
> > > > 9Z.. 
> > > > 
> > > > 
> > > > Tony Stillman, President 
> > > > Radio South, Inc. 
> > > > 139 Altama Connector, Box 322 
> > > > Brunswick, GA 31525 
> > > > 1-800-962-7802 
> > > > www.radiosouthrc.com 
> > > > 
> > &g t; > -----Original Message----- 
> > > > From: nsrca-discussion-bounces at lists.nsrca.org 
> > > > [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron 
> > > > Van Putte 
> > > > Sent: Monday, May 05, 2008 4:09 PM 
> > > > To: General pattern discussion 
> > > > Subject: [NSRCA-discussion] Embarrassing Programming Problem 
> > > > 
> > > > I'm setting up a new airplane on my Futaba 9ZAP transmitter and 
> > using 
> > > > channels 2 and 6 for servos on each elevator half. I have PMX set 
> > > > for channels 2 and 6, mixing channel 2 into channel 6 and 
> > everything 
> > > > works fine, except the servo on channel 6 only moves about 2/3 the 
> > > > throw of the servo on channel 2. I've tried everything I can think 
> > > > of to rectify the problem with no success. In addition, there's a 
> > > > small shift in neutral when going from high rate elevator to 
> > low rate. 
> > > > 
> > > > I st arted with an unused model in the menu, so I don't think 
> > there's 
> > > > any hidden programming lurking. 
> > > > 
> > > > Any ideas? I'll be very irritated to find there's a simple 
> > solution, 
> > > > but I'd also be very grateful to have the problem go away. 
> > > > 
> > > > Ron Van Putte 
> > > > _______________________________________________ 
> > > > NSRCA-discussion mailing list 
> > > > NSRCA-discussion at lists.nsrca.org 
> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> > > > 
> > > > _______________________________________________ 
> > > > NSRCA-discussion mailing list 
> > > > NSRCA-discussion at lists.nsrca.org 
> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> > > 
> > > _______________________________________________ 
> > > NSRCA-discussion mailing list 
> > > NSRCA-discussion at lists.nsrca.org 
> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussio n 
> > _______________________________________________ 
> > NSRCA-discussion mailing list 
> > NSRCA-discussion at lists.nsrca.org 
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> 
> _______________________________________________ 
> NSRCA-discussion mailing list 
> NSRCA-discussion at lists.nsrca.org 
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080505/92db47ba/attachment.html