<html><body>
<DIV>Both were assembled around 4 PM for beer on Friday....</DIV>
<DIV> </DIV>
<DIV class=signature id=signature>--<BR>Vicente "Vince" Bortone</DIV>
<DIV> </DIV>
<BLOCKQUOTE style="PADDING-LEFT: 5px; MARGIN-LEFT: 5px; BORDER-LEFT: #1010ff 2px solid">-------------- Original message -------------- <BR>From: Ron Van Putte <vanputte@cox.net> <BR><BR>> I might agree, but it does the same thing with two 9Z transmitters. <BR>> I wonder what the odds are that two transmitters have the same problem. <BR>> <BR>> Ron <BR>> <BR>> On May 5, 2008, at 5:15 PM, vicenterc@comcast.net wrote: <BR>> <BR>> > Ron, <BR>> > <BR>> > I believe that you need to send the radio to Tony for pots <BR>> > adjustment. If the radio is new send it back to Futaba. <BR>> > <BR>> > -- <BR>> > Vicente "Vince" Bortone <BR>> > <BR>> > -------------- Original message -------------- <BR>> > From: Ron Van Putte <VANPUTTE@COX.NET><BR>> > <BR>> > > OK. I caved and went with ailevator. I nulled out the aileron <BR>> > > inputs and everything works as it should, EXCEPT I'm
still
getting a <BR>> > > small neutral shift on both elevators (same direction) when moving <BR>> > > the elevator dual rate switch. <BR>> > > <BR>> > > Ron <BR>> > > <BR>> > > On May 5, 2008, at 3:20 PM, Tony wrote: <BR>> > > <BR>> > > > Ron: <BR>> > > > Why are you re-inventing the wheel? <BR>> > > > Use the Ailvator pre-set mix for dual elevator servos already <BR>> > built <BR>> > > > into the <BR>> > > > 9Z.. <BR>> > > > <BR>> > > > <BR>> > > > Tony Stillman, President <BR>> > > > Radio South, Inc. <BR>> > > > 139 Altama Connector, Box 322 <BR>> > > > Brunswick, GA 31525 <BR>> > > > 1-800-962-7802 <BR>> > > > www.radiosouthrc.com <BR>> > > > <BR>> > &g t; > -----Original Message----- <BR>> > > > From: nsrca-discussion
-bounc
es@lists.nsrca.org <BR>> > > > [mailto:nsrca-discussion-bounces@lists.nsrca.org] On Behalf Of Ron <BR>> > > > Van Putte <BR>> > > > Sent: Monday, May 05, 2008 4:09 PM <BR>> > > > To: General pattern discussion <BR>> > > > Subject: [NSRCA-discussion] Embarrassing Programming Problem <BR>> > > > <BR>> > > > I'm setting up a new airplane on my Futaba 9ZAP transmitter and <BR>> > using <BR>> > > > channels 2 and 6 for servos on each elevator half. I have PMX set <BR>> > > > for channels 2 and 6, mixing channel 2 into channel 6 and <BR>> > everything <BR>> > > > works fine, except the servo on channel 6 only moves about 2/3 the <BR>> > > > throw of the servo on channel 2. I've tried everything I can think <BR>> > > > of to rectify the problem with no success. In addition, there's a <BR>> > > > small shift in neutral
when
going from high rate elevator to <BR>> > low rate. <BR>> > > > <BR>> > > > I st arted with an unused model in the menu, so I don't think <BR>> > there's <BR>> > > > any hidden programming lurking. <BR>> > > > <BR>> > > > Any ideas? I'll be very irritated to find there's a simple <BR>> > solution, <BR>> > > > but I'd also be very grateful to have the problem go away. <BR>> > > > <BR>> > > > Ron Van Putte <BR>> > > > _______________________________________________ <BR>> > > > NSRCA-discussion mailing list <BR>> > > > NSRCA-discussion@lists.nsrca.org <BR>> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion <BR>> > > > <BR>> > > > _______________________________________________ <BR>> > > > NSRCA-discussion mailing list <BR>> > > > NSRCA-discussion@lists.nsrca.or
g <BR>
> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion <BR>> > > <BR>> > > _______________________________________________ <BR>> > > NSRCA-discussion mailing list <BR>> > > NSRCA-discussion@lists.nsrca.org <BR>> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussio n <BR>> > _______________________________________________ <BR>> > NSRCA-discussion mailing list <BR>> > NSRCA-discussion@lists.nsrca.org <BR>> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion <BR>> <BR>> _______________________________________________ <BR>> NSRCA-discussion mailing list <BR>> NSRCA-discussion@lists.nsrca.org <BR>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion </BLOCKQUOTE></body></html>