[NSRCA-discussion] Kraft info

[Tony]

Jerry:
The pack that fits that is no longer made.  Ihave some packs that will fit
that are 600mah.  Left me now if you want them.


Tony Stillman, President
Radio South, Inc.
139 Altama Connector, Box 322
Brunswick, GA  31525
1-800-962-7802
www.radiosouthrc.com

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Jerry
Stebbins
Sent: Monday, August 04, 2008 9:51 AM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] Kraft info

Ron, thanks for the response. If you have a few connectors how about 
bringing them up to the Contest. I also need a Tx battery. It says it is a 
650mah pack-no voltage shown.nicad.Looks like a normal square JR pack. If 
you have something like that bring it along too.
Thanks--see you Saturday--
Jerry
----- Original Message ----- 
From: "Ron Van Putte" <vanputte at cox.net>
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Sent: Sunday, August 03, 2008 10:07 PM
Subject: Re: [NSRCA-discussion] Kraft info


> The Kraft connectors were called Multicon as I remember.  I still  have a 
> few connectors.  However, why not just splice in some modern  JR/Hitec/Air

> Z connectors and avoid an extra place to fail on each  servo?
>
> I'm also planning on going to the Ballistic Pattern contest in  Huntsville

> this weekend.  I'm finishing up a World Models Intruder  90R and am 
> putting in a Hanno 61 Special.  I seem to remember the  desired pipe 
> length from the glow plug to the baffle in the pipe as  16" to 16.5".  Can

> anyone confirm that?
>
> Ron VP
>
> On Aug 3, 2008, at 9:07 PM, Jerry Stebbins wrote:
>
>> I bought a Tiger Tail III many years ago that was built way back,  and 
>> has nose and wing retracts. It has Kraft servos and Rx, and  a  Signature

>> Series  Kraft Transmitter with it on CH 04, stickered in  1993.
>> Radio was built as a Custom model in March, 1978
>> I am  replacing the Rx and Tx batteries.
>> Several questions I need some help on.
>> 1. Where can I find some 4 pin connectors to make up adapters if I  need 
>> to use a different TX and RX--my old Ham license is long gone..
>> 2. Where can I find some kind of a Manual on the Radio.This plane  has 
>> retracts on the nose gear and wing gear, 2 servos on the  throttle, 
>> normal Ail/Rudder/Elev. setup for the time built.
>> 3. Where can I find xtals to convert to a regular channel.
>> Engine is an OPS 60 almost new-very good shape-and I am cleaning it  up 
>> to use.
>> Plane was flown several times --too fast for the builder, so it  went in 
>> the ceiling in the basement until I found it.
>> My intent was to kit the version (III) and I built a plug for the  fuse 
>> and canopy, and layed out the planforms and airfoils. Then  building and 
>> kitting the 2 meter planes got priority.
>> Fixing it up for Ballistic Pattern--
>> Thanks for any info--
>> Jerry
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion