[NSRCA-discussion] wing tube sleeve hole
Karl G. Mueller
kgamueller at rogers.com
Sat Nov 10 12:05:13 AKST 2007
Nat,
Do the pictures make it more clear of what I was talking about ?
I am not judging at the Worldchamps this time, because I have been
to the last 5. Each time the group of 20 judges has to be made up of
1/3 from judges that have not judged the immediate prior Worldchamps.
It's my turn to sit this one out.
Karl G. Mueller
kgamueller at rogers.com
----- Original Message -----
From: Nat Penton
To: NSRCA Mailing List
Sent: Saturday, November 10, 2007 1:38 PM
Subject: Re: [NSRCA-discussion] wing tube sleeve hole
Thanks Karl. The pictures are nice.
Are you in SantaFe ? Nat
----- Original Message -----
From: Karl G. Mueller
To: NSRCA Mailing List
Sent: Saturday, November 10, 2007 10:38 AM
Subject: Re: [NSRCA-discussion] wing tube sleeve hole
Nat,
First you have to cut a slot thru the foam core at the end of were the
tube
will be. This will serve also as the pocket for the ply tube support.
The slot
size is 3/4" x 2 1/2". All pockets required are cut before the actual
wing core
itself is cut. I trim up all my foam blocks to the same size before
starting to
cut the actual core itself. Make yourself a new cutting-bow out of a
piece of
1" x 2" wood and drill holes for the legs (5/32 dia. music wire or 2 old
main lg's.)
Insert these thru the outward pointing holes right up to the coil. Cut
to length
about 5" below coil. You can solder your wire for the current right to
the
coil.
Now here is the part that takes a little more work.
File or grind small hook shapes at the end of the legs. Make up a
cutting wire
that is when finished about 2" shorter than the distance between the two
legs.
Bend small loops in the cutting wire on both ends. These will hook onto
the
small hooks on the legs.
First burn the starter hole with heated 5/32 wire and than insert the
cutting wire
thru this and hook onto the legs of the bow. The coils in the music wire
(gear legs)
will give you the tension required since the cutting wire is about 2"
shorter
then the uncompressed ends of the legs.
I have been trying to get some pic's attached, but they are too big in
size
to get to the list so I will try to send those direct to you.
Hope this helps.
Karl G. Mueller
kgamueller at rogers.com
----- Original Message -----
From: Nat Penton
To: NSRCA Mailing List
Sent: Friday, November 09, 2007 7:21 PM
Subject: Re: [NSRCA-discussion] wing tube sleeve hole
Karl
At the outboard template position I am having difficulty understanding
how there is room for the cutting bow to work. What am I not seeing.
Thanks Nat
----- Original Message -----
From: Karl G. Mueller
To: NSRCA Mailing List
Sent: Friday, November 09, 2007 10:03 AM
Subject: Re: [NSRCA-discussion] wing tube sleeve hole
Lance,
I have cut the holes for the wing tube socket with a hot wire
and two templates mounted to the work bench at the proper
height to be on center of where the tube hole should be.
The socket hole is cut before cutting the core itself.
You need to make a slot in the core where the end support of the
tube is going to be to insert the template that is mounted to the
bench.
I then burn a small hole thru the center of the templates in the
core with a hot piece of music wire held in a small machine vice
that is guided along a straight edge. Then I thread the wire for the
cutting bow thru that hole and start cutting following the two
templates. Start with a low heat and try the fit. If the fit is too
tight
just increase the voltage a little and go around the templates again
until you achieve the proper fit. Of course you need a variable
power
supply. Sounds more complicated than it really is. Now when you
cut the core, adjust your tip template to get the proper dihedral.
Works
for me.
Karl G. Mueller
kgamueller at rogers.com
----- Original Message -----
From: Lance Van Nostrand
To: NSRCA Mailing List
Sent: Thursday, November 08, 2007 10:46 PM
Subject: Re: [NSRCA-discussion] wing tube sleeve hole
That's a hard one, Mike. Both Terry and I use a similar method.
We had a machine shop make a jig for the cutter. The cutter is a length of
7/8" wing tube with a ground sharp edge, but the jig to hold it has got to
be made presicely. I used to use a seemingly accurate jig made to the plans
provided in a KFactor several years ago, but my results were not good
enough.
--Lance
----- Original Message -----
From: Mike Miller
To: nsrca-discussion at lists.nsrca.org
Sent: Thursday, November 08, 2007 7:08 PM
Subject: [NSRCA-discussion] wing tube sleeve hole
http://www.mackrc.net/patternwings2/index.htm
http://www.nextcraft.com/foamwingsandparts.html
Terry Brox's web site on balsa skinned wings is very good and
does show the drilling of the servo lead hole with a tube and by hand.
Their is some great information on these sites on building foam
core wings. But a very important part of a plug in wing would be the wing
tube sleeve hole in the core, to be straight and parallel to the desired
line centered and at the right angle to set the dihedral. Is there a site
that explains or shows the process of set up and drilling of this hole? If
this step is not perfect looks to me like the wing is dead no matter how
good the skinning process is.
Thanks in advance
Mike
--------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
--------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------------
--
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20071110/33d35ebf/attachment.html
More information about the NSRCA-discussion
mailing list