[NSRCA-discussion] Controll Systems

[Bob Richards]

Similar, but does not appear to be the same. The old one had an aluminum frame that surrounded the servo, and a taller post for the linkage.
   
  Bob R.
  

Rex LESHER <trexlesh at msn.com> wrote:
            Found them.....http://www.horizonhobby.com/Products/Default.aspx?ProdID=KSJ1370    page 25 of the heli option parts and acc.....
   
  Rex
    ----- Original Message ----- 
  From: Rex LESHER 
  To: NSRCA Mailing List 
  Sent: Thursday, January 11, 2007 7:39 PM
  Subject: Re: [NSRCA-discussion] Controll Systems
  

    I'll look, I think I know where to get em....   If I find them, I'll put a link on the list...
   
  Rex
    ----- Original Message ----- 
  From: Ken Thompson 
  To: NSRCA Mailing List 
  Sent: Thursday, January 11, 2007 7:39 PM
  Subject: Re: [NSRCA-discussion] Controll Systems
  

  I think you are talking about the servo saver, I thought they quit making them...actually, I hope you're right, I can think of a few applications.
    ----- Original Message ----- 
  From: Rex LESHER 
  To: NSRCA Mailing List 
  Sent: Thursday, January 11, 2007 9:29 PM
  Subject: Re: [NSRCA-discussion] Controll Systems
  

    I believe they still have them, but now you have to find them in the Helicopter section....
   
  Rex
    ----- Original Message ----- 
  From: jivey61 at bellsouth.net 
  To: NSRCA Mailing List 
  Sent: Thursday, January 11, 2007 7:22 PM
  Subject: Re: [NSRCA-discussion] Controll Systems
  

  Nat
   JR used to make a top bearing brace for the servos. It was a housing that went over the top of the servo and had a adjustable rod to the back of the servo connected to the brace.I use it on the rudder and it solves that problem of top bearing wear. Iv'e had the same problem before due to cable tension.
  We need to see if they are still available or get them to make them again.
   
  Jim Ivey
    ----- Original Message ----- 
  From: Nat Penton 
  To: NSRCA Mailing List 
  Sent: Thursday, January 11, 2007 10:08 PM
  Subject: [NSRCA-discussion] Controll Systems
  

  I'm probably the originator of the .070 carbon-dep system - about 86. Carbon/balsa fuses and kevlar/balsa fuses , are poor combinations, and I'm still using them. Both systems are vulnerable to temp and/or humidity changes and are a pain. Since I've been doing this since 86 I must be a slow learner. No slop but sometimes a trim change every hour.
   
  With balsa fuses, for elev, I plan to go (back) to a balsa dowell pushrod and use a crossover ( MK, or custom ? ) just in front of the stab. Not sure how to handle the rudder, two small hard balsa dowells ? I've had undue kevlar tension ruin two DS8411sa servos on an electric.                              Nat
    
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
    
---------------------------------
    
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070112/051ec771/attachment-0001.html