[NSRCA-discussion] Controll Systems
george w. kennie
geobet at gis.net
Fri Jan 12 11:27:49 AKST 2007
I'm giggling my head off Rex !
----- Original Message -----
From: Rex LESHER
To: NSRCA Mailing List
Sent: Friday, January 12, 2007 2:02 PM
Subject: Re: [NSRCA-discussion] Controll Systems
Man, Georgie, one little typo and it sounds like a disease..... lol
I've been thinking about that very thing... I think you should get one and test it out!!!
----- Original Message -----
From: george w. kennie
To: NSRCA Mailing List
Sent: Friday, January 12, 2007 10:35 AM
Subject: Re: [NSRCA-discussion] Controll Systems
Doesn' that sound like that would allow some flexrex? Oops, missed a key there, sorry, but isn't that what we're trying to eliminate?
(who else)
----- Original Message -----
From: Rex LESHER
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 11:49 PM
Subject: Re: [NSRCA-discussion] Controll Systems
You betcha!!!
Looks like they changed them... No more frame over the top of the entire servo, just an end piece through two servo screws.
Rex
----- Original Message -----
From: Ken Thompson
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 8:44 PM
Subject: Re: [NSRCA-discussion] Controll Systems
thanks Rex.
----- Original Message -----
From: Rex LESHER
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 9:57 PM
Subject: Re: [NSRCA-discussion] Controll Systems
Found them.....http://www.horizonhobby.com/Products/Default.aspx?ProdID=KSJ1370 page 25 of the heli option parts and acc.....
Rex
----- Original Message -----
From: Rex LESHER
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 7:39 PM
Subject: Re: [NSRCA-discussion] Controll Systems
I'll look, I think I know where to get em.... If I find them, I'll put a link on the list...
Rex
----- Original Message -----
From: Ken Thompson
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 7:39 PM
Subject: Re: [NSRCA-discussion] Controll Systems
I think you are talking about the servo saver, I thought they quit making them...actually, I hope you're right, I can think of a few applications.
----- Original Message -----
From: Rex LESHER
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 9:29 PM
Subject: Re: [NSRCA-discussion] Controll Systems
I believe they still have them, but now you have to find them in the Helicopter section....
Rex
----- Original Message -----
From: jivey61 at bellsouth.net
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 7:22 PM
Subject: Re: [NSRCA-discussion] Controll Systems
Nat
JR used to make a top bearing brace for the servos. It was a housing that went over the top of the servo and had a adjustable rod to the back of the servo connected to the brace.I use it on the rudder and it solves that problem of top bearing wear. Iv'e had the same problem before due to cable tension.
We need to see if they are still available or get them to make them again.
Jim Ivey
----- Original Message -----
From: Nat Penton
To: NSRCA Mailing List
Sent: Thursday, January 11, 2007 10:08 PM
Subject: [NSRCA-discussion] Controll Systems
I'm probably the originator of the .070 carbon-dep system - about 86. Carbon/balsa fuses and kevlar/balsa fuses , are poor combinations, and I'm still using them. Both systems are vulnerable to temp and/or humidity changes and are a pain. Since I've been doing this since 86 I must be a slow learner. No slop but sometimes a trim change every hour.
With balsa fuses, for elev, I plan to go (back) to a balsa dowell pushrod and use a crossover ( MK, or custom ? ) just in front of the stab. Not sure how to handle the rudder, two small hard balsa dowells ? I've had undue kevlar tension ruin two DS8411sa servos on an electric. Nat
------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
--------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
------------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070112/659e37d2/attachment-0001.html
More information about the NSRCA-discussion
mailing list