[NSRCA-discussion] cleaning up an engine ?

[Jay Marshall]

Dawn Power Dissolver is the answer. Forget all else!

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Lance Van
Nostrand
Sent: Tuesday, October 03, 2006 9:43 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] cleaning up an engine ?

Paul,
Here are a couple of suggestions from professionally servicing engines:
1. I have an old jug of 5% junk fuel.  Fuel is made of a solvent compatible 
with the goo on your engine.  In fact it dissolves the goo on your engine. 
Soak it good.
2. (this I got from a tip on this list from Earl Haury and it's worth its 
weight in gold) Go get some Dawn Power Dissolver.  The stuff is incredible 
and removing varnish and goo.  But wear plastic gloves, it needs to be 
worked in and it eats skin.
3. gentle warming is good, and I would consider it my #3 option, but after 
the first 2 I never need #3 anymore.

--Lance

----- Original Message ----- 
From: "Paul Horan" <paul.horan at sbcglobal.net>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, October 03, 2006 10:22 AM
Subject: Re: [NSRCA-discussion] cleaning up an engine ?


> John,
>    Until I get some Demon Clean do you have any other alternatives to 
> cleaning up the engine ?
>    How about getting the woodruff key out ?  Should the oven @ 300 work.
> Thanks
> Paul
> ----- Original Message ----- 
> From: "John Pavlick" <jpavlick at idseng.com>
> To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
> Sent: Monday, October 02, 2006 11:49 PM
> Subject: Re: [NSRCA-discussion] cleaning up an engine ?
>
>
>>I use this stuff called "Demon Clean" and it works great. I tried oven
>> cleaner, barbecue grill cleaner, etc. Some of these discolored the 
>> aluminum
>> if you left it on too long. The Demon Clean has proven to be very 
>> effective
>> and a little goes a long way. One can will probably last a few years so 
>> it's
>> really not expensive. You can buy it here:
>> http://www.bj-model-engines.com/Demon-Clean_email_response_11-11-05.html
>>
>> John Pavlick
>> http://www.idseng.com
>>
>>
>>> -----Original Message-----
>>> From: nsrca-discussion-bounces at lists.nsrca.org
>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Paul Horan
>>> Sent: Tuesday, October 03, 2006 12:31 AM
>>> To: nsrca-discussion at lists.nsrca.org
>>> Subject: [NSRCA-discussion] cleaning up an engine ?
>>>
>>>
>>>     I am working on changing the bearing on an OS BXI.  It was
>>> ran hard and put away wet.  Varnish carbon and some rust.
>>>
>>>     Also how do I get the woodruff pin out of the thrust washer ?
>>>   My plan so far is to heat the engine up to about 300 f in the
>>> oven and try to pop the thrust washer off.
>>>
>>> Thanks,
>>> Paul
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>> --
>>> No virus found in this incoming message.
>>> Checked by AVG Free Edition.
>>> Version: 7.1.407 / Virus Database: 268.12.12/461 - Release Date: 10/2/06
>>>
>> --
>> No virus found in this outgoing message.
>> Checked by AVG Free Edition.
>> Version: 7.1.407 / Virus Database: 268.12.12/461 - Release Date: 10/2/06
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion