[NSRCA-discussion] Tee in fuel line for OS140 ?

[vicenterc at comcast.net]

Jay, 

No, I haven't looked the Robart 204.  I prefer to use straight tubing to the carburator to minimize pressure losses in the line when ruining the engine.  Also, the valve introduce another point of failure that could cause problems.

Thanks,

Vicente "Vince" Bortone

-------------- Original message -------------- 
From: "Jay Marshall" <lightfoot at sc.rr.com> 

Have you looked at the Robart 204 Super Fueler? I like it because it is a one way valve when open and a flow thru when shut, and doesn’t require any additional clamps, etc.
 
-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of vicenterc at comcast.net
Sent: Wednesday, November 15, 2006 9:16 AM
To: NSRCA Mailing List; 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] Tee in fuel line for OS140 ?
 
I agree.  I have been doing the same but I use the 90 degree elbows outside to avoid that the carburetor get fuel pressure when fueling (no fuel dot in refueling line).  I bet that you spill some fuel out of the carburetor when you are refueling.  Probably you won't flood the engine but it you loose some fuel.
 
Vicente "Vince" Bortone
 
 
 
-------------- Original message -------------- 
From: "twtaylor" <twtaylor at ftc-i.net> 

> I've been using the 3 line method for years. One line to a YS check valve 
> for vent and two fuel dots and have never flooded the engine. Works slick 
> last long time. 
> 
> -----Original Message----- 
> From: nsrca-discussion-bounces at lists.nsrca.org 
> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Kelly Regan 
> Sent: Tuesday, November 14, 2006 8:08 PM 
> To: NSRCA-discussion at lists.nsrca.org 
> Subject: [NSRCA-discussion] Tee in fuel line for OS140 ? 
> 
> Another question, 
> 
> The fuel tank/line setup in the OS140 manual shows the clunk fuel line 
> running outside of the plane connected with a short length of fuel tube 
> and then run back into the plane to the engine/pu! mp. The short tube is 
> removed for fueling. 
> 
> The instructions indicate that I would need to pinch off the fuel line 
> going to the engine/pump if another system is used. 
> 
> I would like to do 3 lines with 2 fuel dots, one vented, or 2 lines 
> with a tee fitting on the clunk line. 
> 
> Can I do this without having to pinch off the line to the engine/pump 
> each time I fuel up ? 
> 
> Thank you for the help. 
> 
> -- 
> ______________________________________________ 
> 
> Kelly Regan 
> www.reganbrothers.com 
> Home Page: http://mysite.verizon.net/vze6uror/ 
> ______________________________________________ 
> 
> _______________________________________________ 
> NSRCA-discussion mailing list 
> NSRCA-discussion at lists.nsrca.org 
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> 
> 
> __________! _______ ______________________________ 
> NSRCA-discussion mailing list 
> NSRCA-discussion at lists.nsrca.org 
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20061115/67dc6dea/attachment.html 
-------------- next part --------------
An embedded message was scrubbed...
From: "Jay Marshall" <lightfoot at sc.rr.com>
Subject: Re: [NSRCA-discussion] Tee in fuel line for OS140 ?
Date: Wed, 15 Nov 2006 14:53:08 +0000
Size: 718
Url: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20061115/67dc6dea/attachment.mht