[NSRCA-discussion] OS Shadel piston/liner
Bill Glaze
billglaze at triad.rr.com
Mon Mar 6 19:05:47 AKST 2006
Ed:
Yep. Re the coatings referred to above, I've seen some amazing stuff called Heanium. (sp?) It's incredible at holding heat and insulating.
Bill Glaze
----- Original Message -----
From: Ed Miller
To: NSRCA Mailing List
Sent: Monday, March 06, 2006 7:13 PM
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
I could be wrong but it is my understanding the machined type heads are made from bar stock, not die cast material. The greater density of the bar stock material should transfer heat more efficiently than a die cast piece. It is true in racing applications one used to polish the piston tops and combustion chamber to aid in maintaining heat in the combustion chamber ( now there are coating for this ) as well as ward off carbon deposit build up. I think the difference is the ability for a given material to absorb and transfer heat versus the way a surface finish radiates heat.
Ed M.
----- Original Message -----
From: Dave Burton
To: NSRCA Mailing List
Sent: Monday, March 06, 2006 5:49 PM
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
I'm curious too Bill. Then same material should have the same heat characteristics. Surface irregularities from casting should have more effective surface area for greater heat loss.
Of course my thermo and metallurgy courses were a long time ago.
Dave Burton
-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Bill Glaze
Sent: Monday, March 06, 2006 4:42 PM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
Ed:
Just wondered why the machined head would show better heat dissipation. We were always taught that an as-cast surface showed better heat dissipation because of the greater developed surface area. In fact, the "bad example" was the buffed and polished surface. It showed terrible heat characteristics. (Unless, of course, you were looking for heat retention.) The above assumes, of course, that the materials involved were similar or exactly the same. Not quarreling, just curious.
Bill Glaze
----- Original Message -----
From: Ed Miller
To: NSRCA Mailing List
Sent: Monday, March 06, 2006 4:14 PM
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
I'm not sure how one plug going out would cause the engine to go lean. At best having 2 plugs would cause the point of combustion to be a bit earlier OR ( what I believe ) would cause a slightly more efficient burn of the compressed air fuel mixture. Having 2 plugs also may ward off a sudden engine failure due to a blown glow plug. The real advantage in my book of the Mintor head is it is made from bar stock, not cast and therefore has a better thermal efficiency, it sheds the head of combustion quicker and better than the cast head. The lighter weight and second plug which may improve mid range are just a bonus. If I look back at older OS and YS engines, the more "high performance" versions of the same engine had machined bar stock heads. For example the YS61AR and the YS 61R, the AR having besides other improvements a machined bar stock head versus the 61R die cast head.
Ed M.
----- Original Message -----
From: Grow Pattern
To: NSRCA Mailing List
Sent: Monday, March 06, 2006 10:42 AM
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
Randy,
Said another way, if you lose a plug on a twin head, the engine goes lean and usually get very hot :-(
Learned that one the hard way. Using two plugs to fix a rich spot transition on a pipe IMHO is at best a band-aid. Try it and see for yourself :-)
Eric.
----- Original Message -----
From: Dean Pappas
To: randy10926 at comtekmail.com ; NSRCA Mailing List
Sent: Monday, March 06, 2006 10:31 AM
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
Hi Randy,
Mintor parts are available from Aeroslave.
I find that the twin plug head is not absolutely necessary, but it widens the nneedle valve sweet-spot: in the rich direction.
Dean
Dean Pappas
Sr. Design Engineer
Kodeos Communications
111 Corporate Blvd.
South Plainfield, N.J. 07080
(908) 222-7817 phone
(908) 222-2392 fax
d.pappas at kodeos.com
-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of Glenn Hatfield
Sent: Monday, March 06, 2006 9:23 AM
To: nsrca-discussion at lists.nsrca.org
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
Where do you get the mintor head?
Does the dual plug really help any?
Randy
--- ronlock at comcast.net wrote:
From: "Ron Lockhart" <ronlock at comcast.net>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Subject: Re: [NSRCA-discussion] OS Shadel piston/liner
Date: Fri, 3 Mar 2006 17:37:30 -0500
http://www.pspec.com/
Ron Lockhart
.org/mailman/listinfo/nsrca-discussion
--------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
----------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
------------------------------------------------------------------------------
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060306/d0c66685/attachment-0001.html
More information about the NSRCA-discussion
mailing list