[NSRCA-discussion] Engine problem

[Jack Keiser]

How about 1/4 -28?
  ----- Original Message ----- 
  From: jivey61 at bellsouth.net 
  To: NSRCA Mailing List 
  Sent: Saturday, August 26, 2006 6:55 PM
  Subject: Re: [NSRCA-discussion] Engine problem


  Nat
   Isn't the glow plug a 10-28, not a 10-32??????

  Jim Ivey
    ----- Original Message ----- 
    From: Nat Penton 
    To: NSRCA Mailing List 
    Sent: Saturday, August 26, 2006 6:31 PM
    Subject: Re: [NSRCA-discussion] Engine problem


    MattK
    You have just pointed out the easy way to square up the head where the glow plug seats. Take a headless 10-32 bolt and screw into the glow openning from the bottom. Use a lock nut if possible. Chuck the bolt in the lathe and cut the glo washer seat. Who do I bill for this ?   
      ----- Original Message ----- 
      From: Rcmaster199 at aol.com 
      To: nsrca-discussion at lists.nsrca.org 
      Sent: Saturday, August 26, 2006 2:05 PM
      Subject: Re: [NSRCA-discussion] Engine problem


      Are there end mill bits available with a square central locating shoulder built in? Seems that may be the easiet way to get what Earl suggests. Another two step approach might be to use drill rod that just fits the hole as the locator first, locking the head down in the fixture, then switching to the bit and touching the surface to square.

      MattK

      In a message dated 8/26/2006 1:49:06 PM Eastern Standard Time, johnferrell at earthlink.net writes:
        I hate to bug Clarence with the problem. Since the engine runs well the only real problem is it slobbers on the airplane. 

        I have a Lathe and Mill in the shop. Set up will be tricky, the plug is pretty deeply recessed. The risk to the threads by using a pilot rod in the hole is high.

        I believe I will anneal a plug washer and try a little of the liquid gasket goo. If that don't solve the problem I will just accept the mess. 

        John Ferrell    W8CCW
        "My Competition is not my enemy"
        http://dixienc.us/

          ----- Original Message ----- 
          From: Earl Haury 
          To: NSRCA Mailing List 
          Sent: Saturday, August 26, 2006 11:44 AM
          Subject: Re: [NSRCA-discussion] Engine problem


          John

          Assuming that the problem is lack of perpendicularity between the threaded hole and the gasket surface - find a "friend" that will set the thing up in a mill aligned on the threaded hole, then touch the gasket surface with a mill to square. (You might give Clarence a call also - unusual that he would not catch this.)

          Earl


--------------------------------------------------------------------------


      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


--------------------------------------------------------------------------


      No virus found in this incoming message.
      Checked by AVG Free Edition.
      Version: 7.1.405 / Virus Database: 268.11.4/424 - Release Date: 8/21/2006



----------------------------------------------------------------------------


    No virus found in this outgoing message.
    Checked by AVG Free Edition.
    Version: 7.1.405 / Virus Database: 268.11.4/424 - Release Date: 8/21/2006



----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060827/c48fce8e/attachment.html