[NSRCA-discussion] Brio 10 Set up

[Ed Alt]

Ihncheol:
Are you good with a solder iron?  Make your own mode 1 changes if so.  You're just moving wires from one pot to another.  I guess you would have to deal with the wiring on the digital trims too.  Could be done, ofcourse your warranty goes poof!

Ed
  ----- Original Message ----- 
  From: Park, Ihncheol 
  To: 'NSRCA Mailing List' 
  Sent: Friday, April 21, 2006 3:42 PM
  Subject: Re: [NSRCA-discussion] Brio 10 Set up


  I am going with Six-Series with gearbox setup.  E-Flite 40Amp, TP 2100, 4x Futaba S3110, JR 610UL. APC 12x6E.
  I've tried E-Flite 480 on a Pilot Zero 10, but with 3S 2100. It was under 30 oz and flew really well.  I don't think the 1320 will do very well
  I wish Spektrum comes out with Mode 1 for me.

  Ihncheol Park
  P & A Hobbies



------------------------------------------------------------------------------
  From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ed Alt
  Sent: Friday, April 21, 2006 12:45 AM
  To: NSRCA Mailing List
  Subject: Re: [NSRCA-discussion] Brio 10 Set up


  I just finished setting everything up in my "minúsculo Brio".  I grudgingly decided to use the Spektrum.  REALLY wanted to use the 10SXII or 10X, but why buy another receiver.  I like my Spektrum for foamy work, but thinking ahead to having to finally learn how to do useful mixes, fake a rudder DR with a mix etc, get the switches working the way I want, I was being lazy and wanted to avoid it.  So I finally hit the books and have it configured right, the only important piece missing is no expo on rudder.  

  I'm trying the "best recommended setup", i.e. the E-flite Park 480 1010Kv outrunner and the E-flite 40A ESC and starting out with TP 1320's.  Bench tests don't seem too envouraging re. how the vertical will fare with just a 1320, but we'll see.  Seems to sag fairly quickly and it might really need a 2100 pack. The weight is encouraging though and another 2 oz with a TP 2100 isn't going to matter much I guess.  I skipped their little plastic spinner and the all-up weight with Spektrum Rx and 4 JR 281's is 28.9 oz, at the low end of their recommended weight range of 28-34 oz.  I was suprised at how far forward I had to put the battery to achieve a 4" starting balance point from the LE.  It's as far forward as it can go.  Hoping to fly soon if the weather cooperates.

  BTW, has anyone using the 281 digitals noticed that they are never 'happy'?  All of mine run through this cyclic little 'blit' where they can't help but try moving a step and then go back.  It's not an oscillation per se, there are several seconds or more between these 'blits' and it is competely unrelated to whether they are connected to a control surface or not and also unrelated to battery voltage to the receiver.  Also unrelated to receiver type or transmitter used, doing the same thing on a R955S as it does connected to a Spektrum receiver.  No relation to lead length either. It's just what they like to do apparently.  Anyone else seeing this?  Seems like a deadband value issue could be involved.

  Ed
    ----- Original Message ----- 
    From: Steven Maxwell 
    To: NSRCA Mailing List 
    Sent: Sunday, April 16, 2006 5:17 PM
    Subject: Re: [NSRCA-discussion] Brio 10 Set up




    Steven Maxwell


      ----- Original Message ----- 
      From: 
      To: nsrca-discussion at lists.nsrca.org
      Sent: 4/16/2006 4:36:02 PM 
      Subject: [NSRCA-discussion] Brio 10 Set up


      Just wondering which motor, battery, ESC, prop to use on this aircraft.  Also I fly at 6000 msl.  Where would you buy all the accessories and aircraft.  TIA


----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060421/9b025456/attachment.html