[NSRCA-discussion] F3A: F21 observations

Tue Nov 26 05:01:30 AKST 2019

Awesome thanks

________________________________
From: NSRCA-discussion <nsrca-discussion-bounces at lists.nsrca.org> on behalf of Stuart Chale via NSRCA-discussion <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, November 26, 2019 12:40 PM
To: nsrca-discussion at lists.nsrca.org <nsrca-discussion at lists.nsrca.org>
Subject: Re: [NSRCA-discussion] F3A: F21 observations

I have reviewed 3 of 4.  As soon as I have a few hours to go over the Masters I will and send them to Derek.  Hopefully in the next day or two.

A big thanks to James Hiller for making these again.  A lot of work goes into them.

Stuart Chale

On 11/26/2019 5:39 AM, Randy Forbus via NSRCA-discussion wrote:
When are the rest of the power points to come out.

________________________________
From: NSRCA-discussion <nsrca-discussion-bounces at lists.nsrca.org><mailto:nsrca-discussion-bounces at lists.nsrca.org> on behalf of Derek Koopowitz via NSRCA-discussion <nsrca-discussion at lists.nsrca.org><mailto:nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, November 26, 2019 12:59 AM
To: tocdon at netscape.net<mailto:tocdon at netscape.net> <tocdon at netscape.net><mailto:tocdon at netscape.net>; General pattern discussion <nsrca-discussion at lists.nsrca.org><mailto:nsrca-discussion at lists.nsrca.org>
Subject: Re: [NSRCA-discussion] F3A: F21 observations

Look at the current sequences page and in the menu to the left you’ll see a selection for PowerPoint presentations.

Sent from my iPhone

On Nov 25, 2019, at 4:51 PM, Don Szczur via NSRCA-discussion <nsrca-discussion at lists.nsrca.org><mailto:nsrca-discussion at lists.nsrca.org> wrote:

Thanks for forwarding link Jas and Derek.  There are a few pages on the site where I had been looking (Sequences page, Judging page, Canada F3A page) but did not see that chart added until now.

Thanks!

Don

-----Original Message-----
From: james woodward via NSRCA-discussion <nsrca-discussion at lists.nsrca.org><mailto:nsrca-discussion at lists.nsrca.org>
To: Jas S <justanotherflyr at gmail.com><mailto:justanotherflyr at gmail.com>; General pattern discussion <nsrca-discussion at lists.nsrca.org><mailto:nsrca-discussion at lists.nsrca.org>
Sent: Mon, Nov 25, 2019 6:50 pm
Subject: Re: [NSRCA-discussion] F3A: F21 observations

Excellent presentation!  Thanks for pointing it out.
Jim

On Mon, Nov 25, 2019 at 1:41 PM Jas S via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:
https://nsrca.us/index.php/powerpoint-presentations

Jas iP

On Nov 25, 2019, at 2:19 PM, Derek Koopowitz via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:

Jim,

With regard to the golf ball - please look over the PowerPoint presentation on the Nsrca web site for different views of what an appropriate golf ball may look like - page 7.  And yes the entry/exit radii must match the top - page 6.

Best,
Derek

Sent from my iPhone

On Nov 25, 2019, at 10:50 AM, james woodward via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:

Some F21 Manuever Discussion:

1. Golfball - does the entry/exit radii need to match the top?   The maneuver seems to get HUGE.  I'm thinking I need to tighten the initial segment of the top loop.  And then tighten the last segment, to preserve the second 45 down line.  Hit 45, and not be "flat", else the top loop gets even bigger.
2. 1/2 Cuban 8, 2/4 pt, 1/4 Roll, Knife edge 5/8 Loop:  EXCELLENT maneuver for airplane trimming :)  Roll & pitch mix to Rudder viewed every flight haha.  With the Invitation, Left Rudder zero/zero, Right rudder bout 5% down elevator, 1.5% Left Aileron :)
3.  Roller - 1/2 in, 1/2 out - also excellent rudder trim maneuver.
4.  Top Hat - good maneuver after the roller
5.  Funky Humpty (center cross);  Attempting to "fix" the spline after the 1/4 loop integrated just makes it worse.  Must "ping" this upline and just power through into the roll.  Downline - yikes - If you go "out", and looking at the "Bottom" of the plane - Lead with the Rudder that points the direction you want to go, then aileron/elevator.  Wrong Rudder at this point with freeze your brain!@! haha
6.  3/4 8 with 1/2 roll - not too bad - no reason to go too tall
7.  Funky Hammer (Center with looping sections):  Not too bad, but difficult to get the "downline" on center for sure.
8.  Figure 9 with 1.5 snap:  not too bad.  Fly at the end of the box to give room for center top-hat
9.  Top-Hat:  Pretty cool maneuver!  If in doubt, begin early, but the "exit" determines the next maneuver.
10.  1/2 Square loop, 1/2 roll entry:  Must hit the previous "exit" perfectly, then 1/2 Roll entry into 1/2 sure.  1/2 roll entry is a kind of a refreshing take on this maneuver.
11.  45 down line:  1/4 roll, snap, opposite snap, 1/4 roll.  I haven't nailed this yet, but so far, Positive first, Negative second, seems to help hold the 45 line.
12.  1/2 8 sided with 1/2 rolls 1xt,3rd legs.  Not too bad.  Also, try not to get too tall.
13.  Loop with opposite integrated rolls:  cool maneuver - seems to go best when not trying to make too big or over control.  Error on the "power power" for heading up the backside, makes coordinating the aileron/rudder easier.
14.  Positive 2.5 turn spin - nice given P21 has a 2.5 negative spin.
15.  Roll Combo:  Nice manuever - but "exit" into the  Fighter Turn...
16.  Fighter Turn:  3/4 Roll, 3/4 Snap to Upright.  For some reason, flying Left to Right, I hit this OK.  Flying right to Left, its been a visual disaster for me.  This is my worst maneuver so far.  I'll need to specifically practice this one.
17.  Horizontal Square:  1/4 Roll, 1/2 rolls out, 1/4 roll.  So far, looks worse on paper than it is.  Of course, its beneficial  to be a tad higher baseline to fly this.  When pushing the corners, almost no rudder is needed to maintain height.  This is a rudder brain teaser, as you are constantly in/out of rudder same direction while pushing corners, then rolling, then in/out other direction during corner pushes.

Anyone else have some comments yet on F21?
Jim
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20191126/c69e710e/attachment.html>