[NSRCA-discussion] HXT 4mm connectors

Mon Apr 3 03:48:59 AKDT 2017

How did it exactly fail?

On Apr 3, 2017, at 7:41 AM, Matthew Finley <rcfin02 at msn.com<mailto:rcfin02 at msn.com>> wrote:

I switched all of mine over to the red HXT 4mm style connectors. Very happy with them. I personally would not use Anderson power poles as I have seen several fail. My father zeroed a round due to one failing prior to takeoff.

Matthew E Finley
Q.C.I Technical Assistant
248-794-8487 mobile

-------- Original message --------
From: Ron Hansen via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>>
Date: 4/3/17 7:29 AM (GMT-05:00)
To: 'lucky macy' <luckymacy at hotmail.com<mailto:luckymacy at hotmail.com>>, 'General pattern discussion' <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>>, 'Whodaddy Whodaddy' <whodaddy10 at gmail.com<mailto:whodaddy10 at gmail.com>>
Cc: "'Atwood, Mark'" <atwoodm at paragon-inc.com<mailto:atwoodm at paragon-inc.com>>
Subject: Re: [NSRCA-discussion] HXT 4mm connectors

The red 4 mm HXT actually go together as easily as any other bullet style connector if you know how to do it as Ron Van Putte described.

I’ve seen Anderson Power poles fail.

It is certainly much easier to solder the red 4 mm HXT than dean connectors.

From: NSRCA-discussion [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of lucky macy via NSRCA-discussion
Sent: Sunday, April 02, 2017 10:12 PM
To: Whodaddy Whodaddy; General pattern discussion
Cc: Atwood, Mark
Subject: Re: [NSRCA-discussion] HXT 4mm connectors

https://powerwerx.com/anderson-power-powerpole-sb-connectors

Easy choice

On Apr 2, 2017, at 10:06 PM, Whodaddy Whodaddy via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:
Like i said more trouble than its worth

Gary

Sent from my iPhone

On Apr 2, 2017, at 8:28 PM, Atwood, Mark via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:
Thanks all for the online and offline help and advice.  I’m undertaking a complete revamping of all my connectors, from deans to HXT 4mm.  Major pain in the butt, but I’m tired of deans.    Let the soldering begin…

-M

MARK ATWOOD
o.  (440) 229-2502
c.  (216) 316-2489
e.  atwoodm at paragon-inc.com<mailto:atwoodm at paragon-inc.com>

Paragon Consulting, Inc.
5900 Landerbrook Drive, Suite 205, Cleveland Ohio, 44124
www.paragon-inc.com<http://www.paragon-inc.com/>

Powering The Digital Experience

On Apr 2, 2017, at 9:24 PM, Ronald Van Putte via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:

Yeah, I use an opposite connector to help me tap it through the front side as well.

Ron

On Apr 2, 2017, at 8:10 PM, Ron Hansen via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:

That is how I do it too.

But I use an opposite connector to help me tap it through the front side.

Prevents buggering up the connector and helps get the connector properly seated.

Ron Hansen

From: NSRCA-discussion [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ronald Van Putte via NSRCA-discussion
Sent: Sunday, April 02, 2017 8:53 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] HXT 4mm connectors

The way you assemble the HXT connectors is to push the wire through the plastic housing, solder the connector on the wire and tap the connector back into the housing by putting the wires down through a vise and drive the connector into place.

Ron

On Apr 2, 2017, at 7:44 PM, Whodaddy Whodaddy via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:

I used to use them and found them hard to get the bullet back in the plastic after soldering .. not impossible jus more effort than i wanted to put up with ..

Gary

Sent from my iPhone

On Apr 2, 2017, at 7:09 PM, Atwood, Mark via NSRCA-discussion <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>> wrote:
I’m looking to convert all of my equipment to the HXT 4mm Bullet connectors (Red housings).  Can someone that is using them tell me what the standard convention is for wiring these?  It would appear from photos (Hobby king) that the battery side is putting the positive lead on the male bullet (larger housing) and the neg lead on the female bullet (smaller housing).  Is that what most are doing?    Feels backwards to me, but I want to match conventions so I can buy prewired stuff in the future.

-Mark
MARK ATWOOD
o.  (440) 229-2502
c.  (216) 316-2489
e.  atwoodm at paragon-inc.com<mailto:atwoodm at paragon-inc.com>

Paragon Consulting, Inc.
5900 Landerbrook Drive, Suite 205, Cleveland Ohio, 44124
www.paragon-inc.com<http://www.paragon-inc.com/>

Powering The Digital Experience

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

__________ Information from ESET Smart Security, version of malware database 15191 (20170402) __________