[NSRCA-discussion] flutter again

[Michael Ramsey]

Probably 5.0V.

I'm sure that you've seen what the bottom of the aileron looks like on an
F3P model. Would an external frame of carbon fiber help your design here?


On Fri, Sep 13, 2013 at 4:56 PM, George Kennie <geobet4evr at gmail.com> wrote:

> They're running on the BEC voltage. The ailerons are individually powered.
>
>
> On Fri, Sep 13, 2013 at 5:52 PM, Michael Ramsey <milehipilot at gmail.com>wrote:
>
>> But they are aircraft servos right? What voltage are they running on?
>>
>> Paddles are normally used to reduce stick loads on ailerons that are
>> linked to a single servo (or control stick). I don't believe dual servo
>> setups benefit from aileron paddles.
>>
>>
>> On Fri, Sep 13, 2013 at 4:49 PM, George Kennie <geobet4evr at gmail.com>wrote:
>>
>>> I'd be surprised Michael. These are Solar servos and I think they're
>>> either one or two micro/sec and there is no slop anywhere
>>>
>>>
>>> On Fri, Sep 13, 2013 at 5:43 PM, Michael Ramsey <milehipilot at gmail.com>wrote:
>>>
>>>> Could what you're experiencing have anything to do with the deadband
>>>> specification of the servo?
>>>>
>>>>
>>>> On Fri, Sep 13, 2013 at 4:34 PM, George Kennie <geobet4evr at gmail.com>wrote:
>>>>
>>>>> The plane with the tape hinges was modified with balance tabs that I
>>>>> made up at the exact weight of the total surface and added an additional
>>>>> sub small surface at a different incidence and nothing changed.
>>>>>
>>>>>
>>>>> On Fri, Sep 13, 2013 at 5:30 PM, Tom Simes <simestd at netexpress.com>wrote:
>>>>>
>>>>>> On 09/13/13 13:27, George Kennie wrote:
>>>>>> > It's an original foamy design with 3D size surfaces, Michael.
>>>>>> > It's a progression of my Rad-Tad series
>>>>>>
>>>>>> Have you considered taping on some quickie aerodynamic balancing tabs
>>>>>> to
>>>>>> see if the behavior changes?
>>>>>>
>>>>>> --
>>>>>> Tom
>>>>>>
>>>>>> ======================================================================
>>>>>>    "Z80 system stack overflow.  Shut 'er down Scotty, she's
>>>>>>          sucking mud again!" - Error message on XENIX v3.0
>>>>>>
>>>>>> Tom Simes
>>>>>> simestd at netexpress.com
>>>>>> ======================================================================
>>>>>> _______________________________________________
>>>>>> NSRCA-discussion mailing list
>>>>>> NSRCA-discussion at lists.nsrca.org
>>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> NSRCA-discussion mailing list
>>>>> NSRCA-discussion at lists.nsrca.org
>>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>>
>>>
>>>
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>>
>>
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130913/f1784ca7/attachment.html>