[NSRCA-discussion] Transmitter Programming Question

Fri Nov 8 05:36:37 AKST 2013

yes, it does, has had it for about 6-7 years since the 14MZ came out

-----Original Message-----
From: Peter Vogel <vogel.peter at gmail.com>
To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Cc: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Sent: Thu, Nov 7, 2013 11:20 pm
Subject: Re: [NSRCA-discussion] Transmitter Programming Question

No logical switch function in futaba's?  
—
Sent from Mailbox for iPhone

On Thu, Nov 7, 2013 at 8:21 PM, John Gayer <jgghome at comcast.net> wrote:

Don't use a mix.
    You need to determine first what the necessary channel output value    is to turn the glow on. 
    Then set up your plug channel and use throttle stick(J3?) as its    input.
    In AFR, use a "POINT" curve to trigger the output value you need at    15% throttle to turn glow on, you have 9+ points available and I    believe you can move their x-coordinate as well.
    Then, for an ON/OFF switch use a dual rate on the plug channel and    the panel switch of your choice. You should then be able to set up a    second "POINT" curve when the dual rate is active that has all    values set to something that will turn and keep the glow off.

    I don't have a 12FG here to test this but it should work fine.
    John

On 11/7/2013 8:11 PM, Ronald Van Putte      wrote:

OK.  I think I understand.  Pmix the throttle to the      channel the receiver controlled switch is plugged into and use the      throttle as the Pmix switch.  Yes?      

Ron

On Nov 7, 2013, at 8:28 PM, Jas wrote:

Pmix throttle to glow plug and set the points to turn                on where you want

iJason

www.jasonshangar.weebly.com

                On Nov 7, 2013, at 9:04 PM, Ronald Van Putte <vanputter at gmail.com>                wrote:

I think I'll just ignore that.                  

Ron

On Nov 7, 2013, at 8:01 PM, Phil S. wrote:

                          Yes, Ron, switch to JR and it's easy!!!  lol

Phil Spelt, KCRC Emeritus, Past President
AMA 1294 Scientific Leader Member
SPA L-18, Board Member
(865)435-1476v, (865)604-0541c

                          On 11/7/2013 8:17 PM, Ronald Van Putte wrote:                          

I am trying to turn on an onboard glow plug battery on an O.S. .61RF using a receiver controlled switch, so that the glow will be on when the throttle stick position is less than 15% or so and off above that.  I am drawing a blank on how to accomplish it.

I've used the throttle stick as a switch before to get dual rate rudder, but this is different.

I have a Futaba 12 FG transmitter and will be using a Futaba R617 receiver.

Are there any useful suggestions out there?

Ron Van Putte

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

                        _______________________________________________
                        NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

            _______________________________________________
            NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20131108/56a540a8/attachment.html>