[NSRCA-discussion] jr ds8711 servo

[vicenterc at comcast.net]

I think you have to reverse the pot wires too.  Also pots needed cleaning once a month flying on weekends only.    

Vince Bortone
Sent via BlackBerry by AT&T

-----Original Message-----
From: "Atwood, Mark" <atwoodm at paragon-inc.com>
Sender: nsrca-discussion-bounces at lists.nsrca.org
Date: Tue, 12 Feb 2013 11:07:17 
To: General pattern discussion<nsrca-discussion at lists.nsrca.org>
Reply-To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Subject: Re: [NSRCA-discussion] jr ds8711 servo

Now I feel old… Ron help me.  I count on you for my comparitive youth.   I started with heath kit variants of the Kraft K-15 servo (and yes, I built them all).  The were slow, but hard to use.  Had to re-solder the motor wires to reverse direction back then.
Mark Atwood
Paragon Consulting, Inc.  |  President
5885 Landerbrook Drive Suite 130, Cleveland Ohio, 44124
Phone: 440.684.3101 x102  |  Direct: 440-229-2502
Fax: 440.684.3102
mark.atwood at paragon-inc.com<mailto:mark.atwood at paragon-inc.com>  |  www.paragon-inc.com<http://www.paragon-inc.com/>





On Feb 12, 2013, at 10:57 AM, mike mueller <mups1953 at yahoo.com<mailto:mups1953 at yahoo.com>> wrote:


Good point Ron. We've come a long way. I used to use Bonner servo's on my 6 channel MinEx reeds. They were huge and you had to wire them yourself.  Mike
--- On Tue, 2/12/13, Ronald Van Putte <vanputter at gmail.com<mailto:vanputter at gmail.com>> wrote:

From: Ronald Van Putte <vanputter at gmail.com<mailto:vanputter at gmail.com>>
Subject: Re: [NSRCA-discussion] jr ds8711 servo
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org<mailto:nsrca-discussion at lists.nsrca.org>>
Date: Tuesday, February 12, 2013, 9:38 AM

When I saw this e-mail, I chuckled.  Can anyone besides me remember when we used the Kraft KPS-18 servo?  As I remember it had 18 in-oz of torque!  It made up for its lack of torque by being slow too.

Ron Van Putte

On Feb 12, 2013, at 5:40 AM, Gordon Seeling wrote:

> has 403oz of torque, same size as standard servo has anyone used it for rudder servo ??
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org<http://us.mc1247.mail.yahoo.com/mc/compose?to=NSRCA-discussion@lists.nsrca.org>
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<http://us.mc1247.mail.yahoo.com/mc/compose?to=NSRCA-discussion@lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org<mailto:NSRCA-discussion at lists.nsrca.org>
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion