[NSRCA-discussion] NSRCA-discussion Digest, Vol 89, Issue 15

Fri Apr 19 12:36:34 AKDT 2013

are the wings secure are they moving in flight

Date: Fri, 19 Apr 2013 15:26:11 -0500
From: scmcharg at gmail.com
To: nsrca-discussion at lists.nsrca.org
Subject: Re: [NSRCA-discussion] NSRCA-discussion Digest, Vol 89, Issue 15

+.5 on the wing, stab at 0 and 25-37% MAC for CG is an excellent place to start. 

You can calculate MAC of your wing here
http://www.scaleaero.com/mac_page.htm

On Fri, Apr 19, 2013 at 3:23 PM, Anthony Romano <anthonyr105 at hotmail.com> wrote:

Another stab in the dark. (no pun intended)

Is there a weight difference between engines?

Have you checked both that both wings are set to the same incidence? Small differences can cause a serious roll.

I don't remember my cg but was probably around +1/2 degree positive in the wing and it was a solid plane.

Anthony

Date: Fri, 19 Apr 2013 15:18:57 -0500
From: scmcharg at gmail.com
To: nsrca-discussion at lists.nsrca.org
Subject: Re: [NSRCA-discussion] NSRCA-discussion Digest, Vol 89, Issue 15 

Questions: 

1. Is it the same once up in the air regardless of throttle setting?  In other words, does it do the same thing at idle as it does with power?
2. Have you checked your programmable mixing to make sure there isn't anything on that shouldn't be on?  If it is on, could there be a wrong channel selected?

If it flew well before (and this is verified), you need to look at what has changed.  Radio, motor, etc.

Scott

On Fri, Apr 19, 2013 at 3:12 PM, Kc2pk at aol.com <kc2pk at aol.com> wrote:

The plane takes off climbing and rolling left. I can barely be held with stick control, but the deflection requ irked is too much for just trim. I have checked the wing and stab incidences which are close to zero-zero with a Robert incidence meter. Balance is close to the wing tube after 2.5 oz lead attached to the rear of the balsa firewall. The previous owners said that it flew well with a yS 1.60dz, and I am using a 1.40 L. The small difference just can't be the cause. I could understand the pitch problem with a bad CG, but not the rolling.  I have ordered a new incidence meter from central hobbies on the theory that mine Is off, but I really doubt this to to be the problem. Meanwhile I have been flying a Venus2 with an OS 1.20 Ax as well as a curare with a TT .61. I mention this because that are two very different planes and the Hitec aurora 9 transmitter is working flawlessly. The servos are hitec digital 5625's and I see no problem with them on the ground. I wouldn't bo
 thering everyone with this if it were not, really frustrating. I am really asking if anyone  has had a similar problem with this specific airframe. It may be a stab in the dark. Fred

Sent from my iPad

On Apr 19, 2013, at 4:00 PM, nsrca-discussion-request at lists.nsrca.org wrote:

> Send NSRCA-discussion mailing list submissions to
>    nsrca-discussion at lists.nsrca.org
>
> To subscribe or unsubscribe via the World Wide Web, visit
>    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> or, via email, send a message with subject or body 'help' to
>    nsrca-discussion-request at lists.nsrca.org
>
> You can reach the person managing the list at
>    nsrca-discussion-owner at lists.nsrca.org
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of NSRCA-discussion digest..."
>
>
> Today's Topics:
>
>   1. Genesis (Fred Jacobs)
>   2. Re: Genesis (Randy Forbus)
>   3. Re: Genesis (Randy Forbus)
>   4. Re: Genesis (ehaury)
>   5. Re: Genesis (Vicente Planes)
>   6. D4 Judging Seminar Update (Ron Hansen)
>   7. D4 Contest Calendar (Peter G. Van Heusden)
>
>
> ----------------------------------------------------------------------
>
> Message: 1
> Date: Thu, 18 Apr 2013 16:55:16 -0400
> From: Fred Jacobs <kc2pk at icloud.com>
> To: "nsrca-discussion at lists.nsrca.org"
>    <nsrca-discussion at lists.nsrca.org>
> Subject: [NSRCA-discussion] Genesis
> Message-ID: <FA4C8E31-4786-4B0A-A326-93D8ECF406BD at icloud.com>
> Content-Type: text/plain; charset=us-ascii
>
>
> I have recently aquired a Chip Hype Genesis. The plane is powered by aYS 1.40L and balances just ahead of the wing tube with 2.5 oz. lead attached to the rear of the firewall. The problem is that the plane is almost unflyable. I have flown it four times, found it to be all over the sky and have been unable to trim it reliably at all.  I have some questions. Where is the CG recommended to be? Has anyone else had this problem. I have been flying for twenty years in pattern and have never had this problem before. I have discussed the problem with my flying buddy, a masters class flyer of great skill, but without resolution. The fact that I have able to land the plane without damage has been nothing short of miraculous. Any help would be appreciated.  Fred
> Sent from my iPad
>
> ------------------------------
>
> Message: 2
> Date: Thu, 18 Apr 2013 22:54:48 +0000
> From: Randy Forbus <rforbus at hotmail.com>
> To: "nsrca-discussion at lists.nsrca.org"
>    <nsrca-discussion at lists.nsrca.org>
> Subject: Re: [NSRCA-discussion] Genesis
> Message-ID: <COL125-W1896FB62EC2ECB8128F53EA2CF0 at phx.gbl>
> Content-Type: text/plain; charset="iso-8859-1"
>
> what do you mean by unflyable, most modern 2 meter pattern plane balance just at the front edge of the wing tube, or the middle of the wing tube, what does it do to make it unflyable
>
>> From: kc2pk at icloud.com
>> Date: Thu, 18 Apr 2013 16:55:16 -0400
>> To: nsrca-discussion at lists.nsrca.org
>> Subject: [NSRCA-discussion] Genesis
>>
>>
>> I have recently aquired a Chip Hype Genesis. The plane is powered by aYS 1.40L and balances just ahead of the wing tube with 2.5 oz. lead attached to the rear of the firewall. The problem is that the plane is almost unflyable. I have flown it four times, found it to be all over the sky and have been unable to trim it reliably at all.  I have some questions. Where is the CG recommended to be? Has anyone else had this problem. I have been flying for twenty years in pattern and have never had this problem before. I have discussed the problem with my flying buddy, a masters class flyer of great skill, but without resolution. The fact that I have able to land the plane without damage has been nothing short of miraculous. Any help would be appreciated.  Fred
>> Sent from my iPad
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130418/544761f0/attachment-0001.html>
>
> ------------------------------
>
> Message: 3
> Date: Thu, 18 Apr 2013 22:57:40 +0000
> From: Randy Forbus <rforbus at hotmail.com>
> To: "nsrca-discussion at lists.nsrca.org"
>    <nsrca-discussion at lists.nsrca.org>
> Subject: Re: [NSRCA-discussion] Genesis
> Message-ID: <COL125-W18D95C57FE5138A83E8726A2CF0 at phx.gbl>
> Content-Type: text/plain; charset="iso-8859-1"
>
> Besides the cg I would be looking at the wing and stab incidences, .5 positive on the wing is a good place to start and 0 on the stab.
>
>> From: kc2pk at icloud.com
>> Date: Thu, 18 Apr 2013 16:55:16 -0400
>> To: nsrca-discussion at lists.nsrca.org
>> Subject: [NSRCA-discussion] Genesis
>>
>>
>> I have recently aquired a Chip Hype Genesis. The plane is powered by aYS 1.40L and balances just ahead of the wing tube with 2.5 oz. lead attached to the rear of the firewall. The problem is that the plane is almost unflyable. I have flown it four times, found it to be all over the sky and have been unable to trim it reliably at all.  I have some questions. Where is the CG recommended to be? Has anyone else had this problem. I have been flying for twenty years in pattern and have never had this problem before. I have discussed the problem with my flying buddy, a masters class flyer of great skill, but without resolution. The fact that I have able to land the plane without damage has been nothing short of miraculous. Any help would be appreciated.  Fred
>> Sent from my iPad
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130418/8afb4d98/attachment-0001.html>
>
> ------------------------------
>
> Message: 4
> Date: Thu, 18 Apr 2013 18:08:58 -0500
> From: ehaury <ejhaury at comcast.net>
> To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
> Subject: Re: [NSRCA-discussion] Genesis
> Message-ID: <AA02D9AE-28D1-4E0A-8752-C3B011C270F3 at comcast.net>
> Content-Type: text/plain; charset="us-ascii"
>
> Sure you don't have + expo w a Futaba TX?
>
> Sent from my iPhone
>
> On Apr 18, 2013, at 5:57 PM, Randy Forbus <rforbus at hotmail.com> wrote:
>
>> Besides the cg I would be looking at the wing and stab incidences, .5 positive on the wing is a good place to start and 0 on the stab.
>>
>>> From: kc2pk at icloud.com
>>> Date: Thu, 18 Apr 2013 16:55:16 -0400
>>> To: nsrca-discussion at lists.nsrca.org
>>> Subject: [NSRCA-discussion] Genesis
>>>
>>>
>>> I have recently aquired a Chip Hype Genesis. The plane is powered by aYS 1.40L and balances just ahead of the wing tube with 2.5 oz. lead attached to the rear of the firewall. The problem is that the plane is almost unflyable. I have flown it four times, found it to be all over the sky and have been unable to trim it reliably at all. I have some questions. Where is the CG recommended to be? Has anyone else had this problem. I have been flying for twenty years in pattern and have never had this problem before. I have discussed the problem with my flying buddy, a masters class flyer of great skill, but without resolution. The fact that I have able to land the plane without damage has been nothing short of miraculous. Any help would be appreciated. Fred
>>> Sent from my iPad
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130418/9c9272cd/attachment-0001.html>
>
> ------------------------------
>
> Message: 5
> Date: Thu, 18 Apr 2013 18:29:58 -0500
> From: Vicente Planes <vicenterc at comcast.net>
> To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
> Cc: General pattern discussion <nsrca-discussion at lists.nsrca.org>
> Subject: Re: [NSRCA-discussion] Genesis
> Message-ID: <C4F17E25-3ACC-47E0-BD05-559E969C2B49 at comcast.net>
> Content-Type: text/plain; charset="us-ascii"
>
> Combined with really bad servos.
>
> Sent from my iPhone
>
> On Apr 18, 2013, at 6:08 PM, ehaury <ejhaury at comcast.net> wrote:
>
>> Sure you don't have + expo w a Futaba TX?
>>
>> Sent from my iPhone
>>
>> On Apr 18, 2013, at 5:57 PM, Randy Forbus <rforbus at hotmail.com> wrote:
>>
>>> Besides the cg I would be looking at the wing and stab incidences, .5 positive on the wing is a good place to start and 0 on the stab.
>>>
>>>> From: kc2pk at icloud.com
>>>> Date: Thu, 18 Apr 2013 16:55:16 -0400
>>>> To: nsrca-discussion at lists.nsrca.org
>>>> Subject: [NSRCA-discussion] Genesis
>>>>
>>>>
>>>> I have recently aquired a Chip Hype Genesis. The plane is powered by aYS 1.40L and balances just ahead of the wing tube with 2.5 oz. lead attached to the rear of the firewall. The problem is that the plane is almost unflyable. I have flown it four times, found it to be all over the sky and have been unable to trim it reliably at all. I have some questions. Where is the CG recommended to be? Has anyone else had this problem. I have been flying for twenty years in pattern and have never had this problem before. I have discussed the problem with my flying buddy, a masters class flyer of great skill, but without resolution. The fact that I have able to land the plane without damage has been nothing short of miraculous. Any help would be appreciated. Fred
>>>> Sent from my iPad
>>>> _______________________________________________
>>>> NSRCA-discussion mailing list
>>>> NSRCA-discussion at lists.nsrca.org
>>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>> _______________________________________________
>>> NSRCA-discussion mailing list
>>> NSRCA-discussion at lists.nsrca.org
>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130418/ee20b5e4/attachment-0001.html>
>
> ------------------------------
>
> Message: 6
> Date: Thu, 18 Apr 2013 22:08:55 -0400
> From: "Ron Hansen" <rcpilot at wowway.com>
> To: "NSCRA Discussion List" <nsrca-discussion at lists.nsrca.org>
> Subject: [NSRCA-discussion] D4 Judging Seminar Update
> Message-ID: <000901ce3ca2$d8746bc0$895d4340$@wowway.com>
> Content-Type: text/plain; charset="us-ascii"
>
> I posted directions to the D4 Judging Seminar on RCUniverse.
>
>
>
> The classroom stuff will be at the Grove City Church of the Nazarene.
>
>
>
> Contact me if you have any questions.
>
>
>
> Thanks
>
>
>
> __________ Information from ESET Smart Security, version of virus signature
> database 8243 (20130418) __________
>
> The message was checked by ESET Smart Security.
>
> http://www.eset.com
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130418/8e1b226a/attachment.html>
>
> ------------------------------
>
> Message: 7
> Date: Fri, 19 Apr 2013 10:33:03 -0400
> From: "Peter G. Van Heusden" <petervh at malibutech.com>
> To: "nsrca-discussion at lists.nsrca.org"
>    <nsrca-discussion at lists.nsrca.org>
> Cc: "Peter G. Van Heusden" <petervh at malibutech.com>
> Subject: [NSRCA-discussion] D4 Contest Calendar
> Message-ID:
>    <CC83E936118F134EA73F2A277E181CC72A39E0DD51 at selfridge.malibutech.com>
> Content-Type: text/plain; charset="us-ascii"
>
>
> Tom Brett Memorial Pattern Contest
> September 7-8, 2013
>
> Last chance before district championship to get points.
>
> Hope to see everybody here.
> Flyer attached.
>
> Let's get flying
>
> Peter G. VanHeusden
>
> -------------- next part --------------
> An HTML attachment was scrubbed...
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130419/affb2fb3/attachment-0001.html>
> -------------- next part --------------
> A non-text attachment was scrubbed...
> Name: Tom Brett Memorial Pattern Contest_2013.pdf
> Type: application/pdf
> Size: 407079 bytes
> Desc: Tom Brett Memorial Pattern Contest_2013.pdf
> URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130419/affb2fb3/attachment-0001.pdf>
>
> ------------------------------
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> End of NSRCA-discussion Digest, Vol 89, Issue 15
> ************************************************
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-- 
Scott A. McHarg
Sr. Systems Engineer - Infrastructure

_______________________________________________ NSRCA-discussion mailing list NSRCA-discussion at lists.nsrca.org http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-- 
Scott A. McHarg
Sr. Systems Engineer - Infrastructure

_______________________________________________ NSRCA-discussion mailing list NSRCA-discussion at lists.nsrca.org http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 		 	   		  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20130419/13ef6270/attachment.html>