[NSRCA-discussion] Plettenberg 30-10 evo and Jeti ESC

[Robert Campbell]

Robert,

PS.  Ron taught me how to do the Kabuki Dance.


Rob
  ----- Original Message ----- 
  From: Ronald Van Putte 
  To: General pattern discussion 
  Sent: Wednesday, March 14, 2012 10:36 PM
  Subject: Re: [NSRCA-discussion] Plettenberg 30-10 evo and Jeti ESC


  Robert - There's your problem.  The Jeti Advance readjusts the endpoints every time you turn it on.  I had a Jeti 90 Advance and I solved the problem by using a dual rate throttle.  You turn on the radio system with the throttle rate at 100% and "show" the ESC what full throttle land idle ooks like.  Then you go to low rate throttle and fly.  My low rate throttle setting was +/- 70% for the motor I was using.  You'l have to experiment with your motor.


  Ron Van Putte


  On Mar 14, 2012, at 10:25 PM, Robert Green wrote:


    Running a Jeti 90 Advance


----------------------------------------------------------------------------

    From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Robert Green
    Sent: Wednesday, March 14, 2012 9:30 PM
    To: 'Robert Campbell'; 'General pattern discussion'
    Subject: Re: [NSRCA-discussion] Plettenberg 30-10 evo and Jeti ESC

    Hi Rob, the Static amps on the ground is 81 amps.  My throttle is limited to 85 percent.  Even changed out the speed controller and the same thing happened.   Really wish i knew what was going on?


----------------------------------------------------------------------------

    From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Robert Campbell
    Sent: Wednesday, March 14, 2012 9:18 PM
    To: General pattern discussion
    Subject: Re: [NSRCA-discussion] Plettenberg 30-10 evo and Jeti ESC

    Robert,

    Which Jeti are you running?  Advance or Spin?  Just a guess, but all the outrunners I've run require low timing advance and some require fixed end points and the throttle to be limited to 70 percent or so.  Also, have your checked your set-up on a watt meter?  Sometimes our set-ups pull more current than we were expecting and the ESC over current protection kicks in.

    Hope this helps.


    Rob
      ----- Original Message -----
      From: Robert Green
      To: 'General pattern discussion'
      Sent: Wednesday, March 14, 2012 8:19 PM
      Subject: [NSRCA-discussion] Plettenberg 30-10 evo and Jeti ESC

      Is anyone out there running this combo.  Went flying today, and had some issue with the speed controller cutting out when i was setting up for my approach into the pattern.  I was pulling up and advanced the throttle to do an reverse cuban eight to get into my pattern, when the motor suddenly quit.  I pulled the throttle back and advanced it once again and the motor came back it did this on every flight except the first flight where i had no issues whatsoever.  my setting are high timing for the motor, low cut off voltage, acceleration high,


      thnaks in advance

--------------------------------------------------------------------------

      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion




------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20120315/d8aa755b/attachment.html>