[NSRCA-discussion] Servo centering/tester

[Houdini76 at aol.com]

Vexa Control makes two units, the $75 ServoXciter which offers  many servo 
(and receiver) testing capabilities (I use this at the  field) and the $25 
ServoXciter Jr. which will get the centering job done  and run a few other 
tests.
 
_http://www.vexacontrol.com/_ (http://www.vexacontrol.com/) 
 
Rob
 
 
In a message dated 5/18/2011 12:43:12 A.M. Eastern Daylight Time,  
d_bodary at yahoo.com writes:

Jr MatchMaker will center the servos. It has two ports  one for centering 
the servos. you just put the dial in the middle. The  other two ports are for 
checking servos the dial controls the speed. I  got this idea from Troy 
Newman. The matchmaker also works well for  checking pots as you can set the 
speed to slow and look for any dead  spots or chattering.

--- On Tue, 5/17/11, Doug Cronkhite  <seefo at san.rr.com> wrote:


From:  Doug Cronkhite <seefo at san.rr.com>
Subject: Re:  [NSRCA-discussion] Servo centering/tester
To: "General pattern  discussion" <nsrca-discussion at lists.nsrca.org>
Cc: "General  pattern discussion" <nsrca-discussion at lists.nsrca.org>
Date:  Tuesday, May 17, 2011, 1:43 PM


I don't think that's what he meant.




Sent from my iPhone

On May 17, 2011, at 10:38 AM, Dennis Bodary <_d_bodary at yahoo.com_ 
(mip://038d20b8/mc/compose?to=d_bodary@yahoo.com) >  wrote:




   JR MatchMaker Part#JRPA915

--- On  Tue, 5/17/11, Mark Atwood <_atwoodm at paragon-inc.com_ 
(mip://038d20b8/mc/compose?to=atwoodm@paragon-inc.com) >  wrote:


From:  Mark Atwood <_atwoodm at paragon-inc.com_ 
(mip://038d20b8/mc/compose?to=atwoodm@paragon-inc.com) >
Subject:  [NSRCA-discussion] Servo centering/tester
To: "General  pattern discussion" <_nsrca-discussion at lists.nsrca.org_ 
(mip://038d20b8/mc/compose?to=nsrca-discussion@lists.nsrca.org) >
Date:  Tuesday, May 17, 2011, 1:31 PM


 
Does anyone use a simple  servo centering device when installing servo's 
short of  hooking up the Tx and Rx?   I know there's a variety of  servo 
testers that will center the servo, just looking for  the best/least expensive 
setup.  Any suggestions?  I'm always scrambling to find a battery/regulator/Rx 
 and then bind it and set it up just to center a servo.  


thanks!




 
Mark  Atwood
Paragon  Consulting, Inc.  |  President
5885 Landerbrook Drive  Suite 130, Cleveland Ohio, 44124 
Phone:  440.684.3101 x102  |  Fax:  440.684.3102
_mark.atwood at paragon-inc.com_ 
(mip://038d20b8/mc/compose?to=mark.atwood@paragon-inc.com)   |   (http://www.paragon-inc.com/) _www.paragon-inc.com_ 
(http://www.paragon-inc.com/) 












-----Inline  Attachment Follows-----

_______________________________________________
NSRCA-discussion  mailing list
_NSRCA-discussion at lists.nsrca.org_ 
(mip://038d20b8/mc/compose?to=NSRCA-discussion@lists.nsrca.org) 
 (http://lists.nsrca.org/mailman/listinfo/nsrca-discussion) 
_http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_ 
(http://lists.nsrca.org/mailman/listinfo/nsrca-discussion) 




_______________________________________________
NSRCA-discussion  mailing list
_NSRCA-discussion at lists.nsrca.org_ 
(mip://038d20b8/mc/compose?to=NSRCA-discussion@lists.nsrca.org) 
_http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_ 
(http://lists.nsrca.org/mailman/listinfo/nsrca-discussion) 



-----Inline  Attachment Follows-----

_______________________________________________
NSRCA-discussion  mailing list
_NSRCA-discussion at lists.nsrca.org_ 
(mip://038d20b8/mc/compose?to=NSRCA-discussion@lists.nsrca.org) 
_http://lists.nsrca.org/mailman/listinfo/nsrca-discussion_ 
(http://lists.nsrca.org/mailman/listinfo/nsrca-discussion) 



_______________________________________________
NSRCA-discussion  mailing  list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20110518/98e2706c/attachment.html>