[NSRCA-discussion] exhaust temp of a ys 1.75

[Pete Cosky]

Find someone with a TIG that knows how to use it properly. I would check a custom car shop or someplace that does fire engines.

"Robert L. Beaubien" <rob at koolsoft.com> wrote:

>I would think that JB Weld would suffer quick degradation at those
>temperatures.   It's more of an epoxy than a weld.
>
> 
>
>- Robert Beaubien
>
>- D7 Webmaster
>
>-
>
>"No trees were harmed in the sending of this message, however a large
>number of electrons were terribly inconvenienced."
>
> 
>
>From: nsrca-discussion-bounces at lists.nsrca.org
>[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Jay
>Marshall
>Sent: Saturday, December 10, 2011 7:31 PM
>To: 'General pattern discussion'
>Subject: Re: [NSRCA-discussion] exhaust temp of a ys 1.75
>
> 
>
>Would JBWeld work?
>
> 
>
>Jay Marshall
>
> 
>
>From: nsrca-discussion-bounces at lists.nsrca.org
>[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Randy
>Forbus
>Sent: Saturday, December 10, 2011 6:13 PM
>To: nsrca-discussion at lists.nsrca.org
>Subject: Re: [NSRCA-discussion] exhaust temp of a ys 1.75
>
> 
>
>thats  probably a good idea that durafix is low temp repair, I did fix a
>muller header with it though
>
>________________________________
>
>From: jh102649 at speakeasy.net
>Date: Sat, 10 Dec 2011 15:52:42 -0700
>To: nsrca-discussion at lists.nsrca.org
>Subject: Re: [NSRCA-discussion] exhaust temp of a ys 1.75
>
>Mike - 
>
> 
>
>The aluminum in our mufflers and headers is very thin. Unless you are
>really good at joining thin sections I would take it to a machine shop.
>Here in New Mexico I have had good luck. Once I find a shop that can do
>the job I talk directly to the craftsman. Most of these jobs take only a
>few minutes and for $10 or $15 bucks they are usually willing to do it
>on their lunch hour. Doing it through the shop itself is ok too, you'll
>probably pay the shop's minimum.
>
> 
>
>Jeff Hill
>
>On Dec 10, 2011, at 3:08 PM, Michael S. Harrison wrote:
>
>	 
>
>	(For all of you out there, can anyone tell me the exhaust temp
>approximately of a YS 1.75.  I am building a Xurama and the muffler has
>to be shortened(tuny's build thread).  I nedd to know if anyone has
>knowledge how to solder aluminum and if you might have a site that would
>help me.  I believe that there is a flus and an aluminum solder to do
>that.  please let me know if you have any info on that.
>
>	Thanks
>
>	Mike  
>
>	_______________________________________________
>	NSRCA-discussion mailing list
>	NSRCA-discussion at lists.nsrca.org
>	http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> 
>
>
>_______________________________________________ NSRCA-discussion mailing
>list NSRCA-discussion at lists.nsrca.org
>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>
>_______________________________________________
>NSRCA-discussion mailing list
>NSRCA-discussion at lists.nsrca.org
>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion