[NSRCA-discussion] MG Servos to use

[Vicente "Vince" Bortone]

Dave, 



What motor are you using?  I am building one.  I am planing to use 9411 on elevators (max ~20-25 degrees).  8411 on ailerons (max 15-20 degrees) and 8611 on rudder  (max ~35-40) degrees.  Using the Scorpion F3A motor.   I think I should be fine with this se t up for IMAC .  Any suggestions welcome.      

Vicente "Vince" Bortone 

----- Original Message ----- 
From: "Dave" <DaveL322 at comcast.net> 
To: "General pattern discussion" < nsrca -discussion at lists. nsrca .org> 
Sent: Monday, March 29, 2010 10:00:32 AM GMT -06:00 US/Canada Central 
Subject: Re: [NSRCA-discussion] MG Servos to use 




Matt, 



I put a little bit of flight time on an EF 78” Extra electric 2 weekends ago (It has 8711 HVs running on unregulated 5 cell Nimh – so figure 400 oz/in and 0.15 sec – definitely overkill).  My personal opinion is that 100 oz/in of digital torque is fine for elevator (2 servos), but more like 150 oz for ailerons (2 servos) and 200 oz for rudder, especially if you are going to have 3D throws. 



Spektrum has some relatively new servos – 

6010 is $40, metal gear, 100 oz/in, 0.14 sec 

6030 is $85, titanium gear, 278, 0.15 sec 

6040 is $80, titanium gear, 167, 0.08 sec 



I used some of the 821 “standard” servos (composite gear, 88, 0.15) on the ailerons of my 120 mph Sundowner and they are solid (not fast, but solid). 



I’ve been flying a 65” Vyper from 3DHobby, and the first few flights were with JR 8717 on the ailerons, and then some JR 8411sa’s, and now I have some Spektrum 6030s to try (next time the weather clears).  The 8717s draw a lot of current, but have absolutely stunning performance – very stable roll trim, smooth response for pattern stuff, and very positive/crisp for snaps and 3D work (and yes, pricey at $140, but I think an example of getting more performance for more $$$). 



 Regards, 



Dave Lockhart 

Team Horizon/JR/Spektrum 






From: nsrca -discussion-bounces at lists. nsrca .org [mailto: nsrca -discussion-bounces at lists. nsrca .org] On Behalf Of rcmaster199 at aol.com 
Sent: Monday, March 29, 2010 10:20 AM 
To: nsrca -discussion at lists. nsrca .org 
Subject: [NSRCA-discussion] MG Servos to use 





Hey folks, 





I need some MG Digital Servos to use on the 78" Xtra. These need to have at least 100 in-ozs of torque and I prefer at least 0.15 sec transits. I've looked at Airtronics and JR.....For cored servos prices are not too bad but for coreless, prices are too high. I prefer coreless. 





Would someone with experience with the other brands shed some light on this? I'd like reasonably priced (50-70$ as opposed to 120$), metal geared servos with torque and speed shown above. I started to look at Hitec but I understand these need some kind of programmer!? The need is 4 at about 100 in-ozs and 1 at about 170 in-ozs 





Thanks 





Matt Kebabjian 
_______________________________________________ NSRCA-discussion mailing list NSRCA-discussion at lists. nsrca .org http://lists. nsrca .org/mailman/listinfo/ nsrca -discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20100330/90c459c0/attachment.html>