[NSRCA-discussion] Need Dremel Part

[Phil Spelt]

VERY well said, Jon...

At 09:38 AM 7/7/2010, you wrote:


>Jon Lowe
>
>
>-----Original Message-----
>From: Ron Van Putte <vanputte at cox.net>
>To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
>Sent: Wed, Jul 7, 2010 8:25 am
>Yeah, but if you didn't have Houston Schweitzer around, you wouldn't 
>know how to use that Droid!  Everytime you want to do something, you 
>hand it to him!!
>
>Jon
>
>To get the record straight: I retired from the USAF in 1979, from 
>Civil Service in 1997 and started collecting Social Security the 
>same year. You youngsters will never see Social Security, so I thank 
>each and every one of you for my monthly check.
>
>Now about keeping up with the times: My cell phone is a Droid 
>Incredible. What's yours whippersnapper?
>
>Ron VP
>
>On Jul 7, 2010, at 8:12 AM, Atwood, Mark wrote:
>
> > Better screws on the coffin lid??
> >
> > Seriously though, as one who still has my Dremel from 1973 (I 
> know, > you were already retired then right??) I finally broke down 
> and > bought a new one and have been wondering why I waited so 
> long. The > newer cordless lithium powered units rock. Take the plunge...
> >
> > Mark Atwood
> > Paragon Consulting, Inc. | President
> > 5885 Landerbrook Drive Suite 130, Cleveland Ohio, 44124
> > Phone: 440.684.3101 x102 | Fax: 440.684.3102
> > <mailto:mark.atwood at paragon-inc.com>mark.atwood at paragon-inc.com | 
> www.paragon-inc.com
> >
> >
> > -----Original Message-----
> > From: 
> <mailto:nsrca-discussion-bounces at lists.nsrca.org>nsrca-discussion-bounces at lists.nsrca.org 
> [mailto:nsrca-> discussion-bounces at lists.nsrca.org] On Behalf Of Ron Van Putte
> > Sent: Tuesday, July 06, 2010 2:58 PM
> > To: General pattern discussion
> > Subject: [NSRCA-discussion] Need Dremel Part
> >
> > I have an old Dremel Freewheeler Model 850 that has a flexible
> > coupler between the motor and the output shaft. This coupler is
> > splined on the inside and the splines finally wore out after 20+
> > years for no reason at all. It's on its third or fourth battery
> > pack, but still worked fine before the coupler gave out. I've tried
> > searching sources for Dremel parts but can't find what I need. I
> > would just buy a new one, but I am stubborn and the son of a Scottish
> > mother, who would rise up out of her grave if I did.
> >
> > Any ideas?
> >
> > Ron Van Putte
> > _______________________________________________
> > NSRCA-discussion mailing list
> > <mailto:NSRCA-discussion at lists.nsrca.org>NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> > _______________________________________________
> > NSRCA-discussion mailing list
> > <mailto:NSRCA-discussion at lists.nsrca.org>NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>_______________________________________________
>NSRCA-discussion mailing list
><mailto:NSRCA-discussion at lists.nsrca.org>NSRCA-discussion at lists.nsrca.org
>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>_______________________________________________
>NSRCA-discussion mailing list
>NSRCA-discussion at lists.nsrca.org
>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-->There are only two types of aircraft -- fighters and targets.

Phil Spelt, Past President, Knox County Radio Control Society, Inc.
        URL: http://www.kcrctn.com
AMA--1294,  Scientific Leader Member  SPA--177, Board Member
       My URL: http://mywebpages.comcast.net/~chuenkan/
       (865) 435-1476 v  (865) 604-0541 c  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20100707/7762c71c/attachment.html>