[NSRCA-discussion] Need Dremel Part

[Ron Van Putte]

Squealer!

Ron

On Jul 7, 2010, at 8:38 AM, Jon Lowe wrote:

>
>
> Yeah, but if you didn't have Houston Schweitzer around, you  
> wouldn't know how to use that Droid!  Everytime you want to do  
> something, you hand it to him!!
>
> Jon
>
>
> -----Original Message-----
> From: Ron Van Putte <vanputte at cox.net>
> To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
> Sent: Wed, Jul 7, 2010 8:25 am
>
> To get the record straight: I retired from the USAF in 1979, from  
> Civil Service in 1997 and started collecting Social Security the  
> same year. You youngsters will never see Social Security, so I  
> thank each and every one of you for my monthly check.
>
> Now about keeping up with the times: My cell phone is a Droid  
> Incredible. What's yours whippersnapper?
>
> Ron VP
>
> On Jul 7, 2010, at 8:12 AM, Atwood, Mark wrote:
>
> > Better screws on the coffin lid??
> >
> > Seriously though, as one who still has my Dremel from 1973 (I  
> know, > you were already retired then right??) I finally broke down  
> and > bought a new one and have been wondering why I waited so  
> long. The > newer cordless lithium powered units rock. Take the  
> plunge...
> >
> > Mark Atwood
> > Paragon Consulting, Inc. | President
> > 5885 Landerbrook Drive Suite 130, Cleveland Ohio, 44124
> > Phone: 440.684.3101 x102 | Fax: 440.684.3102
> > mark.atwood at paragon-inc.com | www.paragon-inc.com
> >
> >
> > -----Original Message-----
> > From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca->  
> discussion-bounces at lists.nsrca.org] On Behalf Of Ron Van Putte
> > Sent: Tuesday, July 06, 2010 2:58 PM
> > To: General pattern discussion
> > Subject: [NSRCA-discussion] Need Dremel Part
> >
> > I have an old Dremel Freewheeler Model 850 that has a flexible
> > coupler between the motor and the output shaft. This coupler is
> > splined on the inside and the splines finally wore out after 20+
> > years for no reason at all. It's on its third or fourth battery
> > pack, but still worked fine before the coupler gave out. I've tried
> > searching sources for Dremel parts but can't find what I need. I
> > would just buy a new one, but I am stubborn and the son of a  
> Scottish
> > mother, who would rise up out of her grave if I did.
> >
> > Any ideas?
> >
> > Ron Van Putte
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion