[NSRCA-discussion] Servos - Again

[Atwood, Mark]

To add to that, I would no longer be "afraid" of metal gear servos.  The tolerances have gotten much much tighter to where the "slop" factor is no long of concern.  Just my opinion, but I think the Nylon only approach has past it's day.

I'd also be remiss not to suggest you look at Airtronics servos if you're looking at all brands.  They have an entire new line of affordable digitals to choose from, as well as the high end line of digitals.

-Mark
(Team Airtronics...thus the plug).

Mark Atwood
Paragon Consulting, Inc.  |  President
5885 Landerbrook Drive Suite 130, Cleveland Ohio, 44124 
Phone: 440.684.3101 x102  |  Fax: 440.684.3102
mark.atwood at paragon-inc.com  |  www.paragon-inc.com


-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ihncheol Park
Sent: Monday, January 18, 2010 2:20 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] Servos - Again

Tim,

Here are the list of JR servos the were popular so far.

Ailerons : DS9411 
Dual Elevator servos : DS3421
Single Elevator servo : DS8231 (plastic gear).  DS8417 has been discontinued.
Rudder : DS8611

All the above are metal gears.  JR has discontinued all SA servos. If you need plastic/resin geared servos, you will need JRPSG321 and JRPSG911 to convert them to metal output with plastic gears.

You can also substitute DS8611 with DS8411 which can use JRPSG8101 to make it 8411SA.

Hope this helps,

Ihncheol

--- On Mon, 1/18/10, Pascoe,Tim [Burlington] <Tim.Pascoe at ec.gc.ca> wrote:

> From: Pascoe,Tim [Burlington] <Tim.Pascoe at ec.gc.ca>
> Subject: [NSRCA-discussion] Servos - Again
> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
> Date: Monday, January 18, 2010, 12:33 PM
> 
> 
> 
>  
>  
> 
> 
> 
> 
> 
> 
>  
> 
> 
> 
> It’s been
> 3-4 years since I bought servos for a
> pattern plane, and when I went searching for my trusty
> selections for a new
> bird, I discovered that a lot has changed in a short
> time. 
> 
> 
>   
> 
> So –
> I’m looking for suggestions for Elevator,
> Rudder, and Aileron. I recently switched to Futaba for my
> transmitter, but was
> a JR guy previous to that and have always been happy with
> JR servos. I’d
> consider Futaba and Hitec as alternatives as
> well. 
> 
> 
>   
> 
> Thanks,
> 
> 
> 
>   
> 
> Tim
>  
> 
> 
> 
>  
> 
> 
> 
> -----Inline Attachment Follows-----
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion