[NSRCA-discussion] 14MZ springs

[Archie Stafford]

Have to agree with Verne and Tony.  I'm running the RS springs and never had
a problem.  I run them in everything I own.

Arch


-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of
verne at twmi.rr.com
Sent: Friday, March 27, 2009 8:16 AM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] 14MZ springs

I've been using the Radio South springs in my 14mz for the last 4 years. My
original encoders were replaced by Futaba as a routine factory upgrade when
the radio was one-season old but weren't actually causing me any problems. I
had sent the radio in to have a defective trim switch replaced and Futaba
just routinely upgraded the encoders. The RS springs have worked fine for
me.

Verne Koester


---- Tony <tony at radiosouthrc.com> wrote: 
> Adrian:
> I sell HD springs for all transmitters and they are very popular.  I have
> been using them in my 14MZ for several years now, without any problems.  I
> have just changed to the new encoders as a matter of fact.  
> 
> I don't understand the statement that HD springs cause undue wear on the
> encoders.  They are a pivot point, not a pressure point for the
> spring/scissor unit.  There is just not a problem here.
> 
> The only issues with springs is to make sure the loops are large enough so
> the spring can pivot, especially in the grove that is in the plastic
> adjuster in the Futaba units.  If the loop is too small, the top of the
> spring coil will press against the bottom of the adjuster arm and will
> actually flex the adjuster, causing it to break over time.  When the loop
is
> large enough so the coil does not touch the adjuster arm, the spring will
> just pivot in the groove (as it should).  
> 
> I have been flying HD springs since 1981...  literally thousands of
flights
> and never a failure...
>  
> 
> Tony Stillman, President
> Radio South, Inc.
> 139 Altama Connector, Box 322
> Brunswick, GA  31525
> 1-800-962-7802
> www.radiosouthrc.com
> 
> -----Original Message-----
> From: nsrca-discussion-bounces at lists.nsrca.org
> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of
> adriancwong at earthlink.net
> Sent: Thursday, March 26, 2009 8:32 PM
> To: General pattern discussion; General pattern discussion
> Subject: Re: [NSRCA-discussion] 14MZ springs
> 
> Be careful on using springs that is too stiff. I've be warned that was one
> of the reason that can wear out the encoders prematurely.
> 
> Adrian
> 
> -----Original Message-----
> >From: Stuart Chale <schale at optonline.net>
> >Sent: Mar 26, 2009 8:18 PM
> >To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
> >Subject: Re: [NSRCA-discussion] 14MZ springs
> >
> >I don't have the link but they were very easy to install.  Although 
> >Futaba says not to use their regular heavy duty springs I did and have 
> >not had an issue with it.  I suspect many have used the same springs.  
> >The springs that Tony from Radio South sells are stiffer and I guess 
> >could be a problem if Futaba says that their HD springs are too heavy.  
> >I suspect that there are people that have installed them as well without 
> >problems though.
> >The main thing is to make sure that the two loops on each end of the 
> >spring are perpendicular to each other before installing them.  A fine 
> >needle nose plier or thin hemostat makes the job easier.
> >Stuart C.
> >
> >James Oddino wrote:
> >>
> >> I remember seeing an in depth procedure with photos showing how to 
> >> replace the springs in a 14MZ.  Seems like it was on someone's 
> >> website.  I thought I bookmarked it but I can't seem to find it.  
> >> anyone know what I'm talking about?
> >>
> >> Jim O
> >> _______________________________________________
> >> NSRCA-discussion mailing list
> >> NSRCA-discussion at lists.nsrca.org
> >> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>
> >>
> >
> >_______________________________________________
> >NSRCA-discussion mailing list
> >NSRCA-discussion at lists.nsrca.org
> >http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> 
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion