[NSRCA-discussion] JR9303 Throttle cut/hold in airplanesoftware for e-power

[Troy Newman]

two ways to do it.
 
type 1
One go into your throttle curve and seta  switch that will give you a  Curve POS0 and curve POS1 set one of those curves to all Zero values. just run them all down to zero...this will disable the throttle stick. You are fooling the throttle into following a new curve...one that drives the servo to zero throttle and doesn't change as the stick moves up and down.
 
 
type 2
The throttle to throttle mix works...but here is what you are doing in the logic. Throttle to throttle mix says take the current throttle stick position and mix a % of throttle to it. So if you had a mix value of -5% and your throttle stick was at say 35% the mix would take the 35% and subtract the -5% from it. 
 
So the output value would be 30% NET.
 
The way you have it setup now with a 0% at each point you are saying take the current stick position and add or subtract ZERO from it. So you are not doing anything.
 
To make this option work....do this. 
 
Don't use a curve mix. Use a normal linear mix.
Set the values at -125% or even -150% if they will go that high....I don't have my 9303 in front of me right now.
 
This will take the current position of the throttle and subtracts out all values and the throttle should not move. You may need to mess with the stick position value as it appears with your everything works below 1/4 throttle statement means you probably changed this from the default.
 
The stick pos or thro stick function on these mixes allows the mix to turn on or off or change from one mix value to another at a given throttle stick position. Its basically setting the inflection point where the throttle stick activates the mix. If you thro stk value at 1/4 throttle stick then this would make the mix change from POS0 to POS1 at that throttle stick location. This allows you to play with this type of mixing in order to customize it even more than a simple on/off. Example is you can have different mix settings based on your throttle stick location. If you want 3%up elevator with rudder for knife edge. You can use the throttle stick position to change it to 8%up elevator when the throttle is below say 10% and have the same 3% knife edge mix when the throttle is above 10%
 
This allows you to have really 2 mixes or rather mix values built into one mix....Or you can leave one value as ZERO and this will make the mix turn on or off at that point just like it was a switch.
 
After all this is said
 
I prefer the throttle curve method I suggested at first. This is type 1
 
if you have Q's send me a line and I'll work it out with you. I can get my 9303 when I get home and walk you through it.
 
Troy Newman
Team Horizon Hobby / Team JR

________________________________

From: nsrca-discussion-bounces at lists.nsrca.org on behalf of Ihncheol Park
Sent: Fri 3/20/2009 10:03 AM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] JR9303 Throttle cut/hold in airplanesoftware for e-power


Stuart,
 
It is for JR 9303.  The mixing is set for entire range of the throttle stick to have output of 0 on a flip of mixing switch.  It still turns.  It is the only mix that I use switch.  I try to set all other mixes on permanently.   
Somepeople suggested using Heli software for it, but I don't really like it on airplane.
 
Ihncheol


________________________________

From: Stuart Chale <schale at optonline.net>
To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Sent: Friday, March 20, 2009 11:54:11 AM
Subject: Re: [NSRCA-discussion] JR9303 Throttle cut/hold in airplane software for e-power

Depends on the radio, Futaba higher models have throttle hold, or conditions that could be used.  Just set a condition where the throttle is always at 0.
You can probably get more specific info if we know the radio.  On another note I did have a throttle hold set to a switch, rarely used it and forgot about it.  Added a mix assigned to the same switch (14MZ) and when activated the throttle well you figured it out.  Damaged the plane on a dead stick.  Even though I unflipped the switch what I didn't remember is that the throttle stick had to be cycled back to 0 to reset it, a safety feature preventing you from accidentally flipping the throttle hold off with the throttle advanced.  I no longer use a throttle hold.
Stuart

Ihncheol Park wrote: 

	Ok.  I have a question to all those who fly E-power.
	I've been flying a little of e-powered planes, but mostly foamy and small ones.
	Now going with 90 size before starting 2m.
	 
	Is there any way to set throttle cut/hold in Airplane software for entire range of the throttle?
	I've mixed throttle to throttle on a switch to 0 in all 5 point.  It works on idle, but not if I move the throttle stick more than 1/4 throttle.  Motor still turns. 
	 
	Am I missing something?
	 
	I don't want that 19 + inch props turn without my approval!
	 
	Thanks,
	 
	Ihncheol
	
________________________________


	_______________________________________________
	NSRCA-discussion mailing list
	NSRCA-discussion at lists.nsrca.org
	http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
	  

-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/ms-tnef
Size: 9600 bytes
Desc: not available
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20090320/8980098e/attachment.bin>