[NSRCA-discussion] Servos suggestions for a 90 size pattern plane

[Vicente "Vince" Bortone]

Mike, 



I agree.  I am flying the same plane electric and glow (Abbra).  The electric uses around 50-60 mah and the glow 150-200 mah per each Master round.  This is about 1/3 of the power.  For sure, electric planes can use smaller servos. 



VB 
----- Original Message ----- 
From: "mike mueller" <mups1953 at yahoo.com> 
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org> 
Sent: Friday, June 12, 2009 9:24:59 AM GMT -06:00 US/Canada Central 
Subject: Re: [NSRCA-discussion] Servos suggestions for a 90 size pattern plane 


 Tommy I worried about the 3421's until I looked at the size servo's that QQ was running on his Euphoria. He runs dual ailerons on 1 small servo. I'm running 3421 metals on my ailerons on my new Sickle so far so good. It was because of weight and also because I really think an E. plane can get away with less servo. I run it on a 6volt regulated 2 cell lipo. I think everyone is in to the security that overkill allows and that's great if your not worried about the weight. Mike 

--- On Fri, 6/12/09, Tommy Scarmardo <tretas513 at yahoo.com> wrote: 

> From: Tommy Scarmardo <tretas513 at yahoo.com> 
> Subject: Re: [NSRCA-discussion] Servos suggestions for a 90 size pattern plane 
> To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org> 
> Date: Friday, June 12, 2009, 9:13 AM 
> The 3421sa's are great little 
> servos, I have two on elevator on my new ship, but you 
> should be careful where you use them. The motor is 
> stronger than the nylon gear 
> train and is easily stripped under certain conditions. 
> The gears are tiny. 
>   
> tommy s 
> 
> --- On Fri, 6/12/09, mike mueller 
> <mups1953 at yahoo.com> wrote: 
> 
> 
> From: mike mueller <mups1953 at yahoo.com> 
> Subject: Re: [NSRCA-discussion] Servos suggestions for a 90 
> size pattern plane 
> To: "General pattern discussion" 
> <nsrca-discussion at lists.nsrca.org> 
> Date: Friday, June 12, 2009, 7:47 AM 
> 
> 
> 
> How about JR 3421SA on everything but the rudder which 
> would work well with a JR 8321. Mike 
> 
> --- On Fri, 6/12/09, Dean & Melissa Williams <DMWILLIAMS at bigpond.com> 
> wrote: 
> 
> > From: Dean & Melissa Williams <DMWILLIAMS at bigpond.com> 
> > Subject: [NSRCA-discussion] Servos suggestions for a 
> 90 size pattern plane 
> > To: nsrca-discussion at lists.nsrca.org 
> > Date: Friday, June 12, 2009, 7:40 AM 
> > 
> > 
> >  
> >  
> > 
> > 
> >  
> > Hi 
> > Which servos 
>  (brand and #) 
> > would you use for a 90 
> > size pattern plane like the ESM Adrenaline 90 and 
> which 
> > ones on what surfaces 
> > ? 
> > Thanking you for your 
> > sugestions 
> > 
>                                                
> > 
> > Dean (Outback OZ) 
> > 
> > -----Inline Attachment Follows----- 
> > 
> > _______________________________________________ 
> > NSRCA-discussion mailing list 
> > NSRCA-discussion at lists.nsrca.org 
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> 
> 
>       
> _______________________________________________ 
> NSRCA-discussion mailing list 
> NSRCA-discussion at lists.nsrca.org 
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
> 
> 
> 
>       
> -----Inline Attachment Follows----- 
> 
> _______________________________________________ 
> NSRCA-discussion mailing list 
> NSRCA-discussion at lists.nsrca.org 
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


       
_______________________________________________ 
NSRCA-discussion mailing list 
NSRCA-discussion at lists.nsrca.org 
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20090612/c1757123/attachment.html>