[NSRCA-discussion] YS Problem

Tue Jun 2 20:35:09 AKDT 2009

Andrew and I won’t be there to do your wrenching….

Verne

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Atwood, Mark
Sent: Tuesday, June 02, 2009 11:32 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] YS Problem

Unfortunately today was my last day to fly prior to Muncie  (GO D4!!!!!!)

I’ll have to wait and try it there…  And bring a spare motor in case it doesn’t run.

I actually have a spare head that I will put back on (the non CDI head).  So that SHOULD work just fine.  

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Anthony Abdullah
Sent: Tuesday, June 02, 2009 11:30 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] YS Problem

Mark,

I have the El Nino and all the associated equipment (starter, battery, fuel, fuel pump, etc) loaded up and will be headed to the field from work tomorrow.

If you can get ahold of some JB Weld I will see you there.

--- On Tue, 6/2/09, Atwood, Mark <atwoodm at paragon-inc.com> wrote:

From: Atwood, Mark <atwoodm at paragon-inc.com>
Subject: Re: [NSRCA-discussion] YS Problem
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Date: Tuesday, June 2, 2009, 11:04 PM

I’ll read the link…

Sounds good!  You missed a beautiful night to fly.  So did I L

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Anthony Abdullah
Sent: Tuesday, June 02, 2009 10:56 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] YS Problem

None taken :o)

I hope like hell I'm wrong!!!

Attached is a link to a thread in RCU titled "Injector coming out of head"

http://www.rcuniverse.com/forum/m_7197327/anchors_7210131/mpage_1/key_/anchor/tm.htm#7210131

Speaking of YS and fun, I am pulling a half the niter converting my Black Magic to electric... Hmmmmmm Let me tell you, it was NOT fun trying to get the nose ring out, damn that thing was in there good. Other than that it is going fairly well actually almost done staring at it.  

--- On Tue, 6/2/09, Atwood, Mark <atwoodm at paragon-inc.com> wrote:

From: Atwood, Mark <atwoodm at paragon-inc.com>
Subject: Re: [NSRCA-discussion] YS Problem
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Date: Tuesday, June 2, 2009, 10:43 PM

In a word…  Crap!

Anyone else??  I’d like a second opinion!!!! (nothing personal Anthony but your opinion ..well…sucks. lol)   I have a feeling you’re correct though, much to my chagrin.  Not having a good YS moment.

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Anthony Abdullah
Sent: Tuesday, June 02, 2009 10:42 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] YS Problem

Mark,

Bad news, you can not put that back in so it does not pup out again. >From what I have read, that problem isn't really user serviceable. I have read posts of guys pressing them back in and even some guys using JB Weld to keep them in. Usually that is a problem that requires the engine to go back to YS.

Sorry to hear that!

Anthony

--- On Tue, 6/2/09, Atwood, Mark <atwoodm at paragon-inc.com> wrote:

From: Atwood, Mark <atwoodm at paragon-inc.com>
Subject: [NSRCA-discussion] YS Problem
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Date: Tuesday, June 2, 2009, 10:16 PM

The short version…    YS1.70DZ – the brass fitting on the TOP of the head (towards the back) that has the black check valve pressed onto it blew out of the engine in flight!!  Needless to say the motor quit.

It appears to be a pressure fit.    I pressed it back in (I knew this wouldn’t work, but what the heck), started the engine.  It idled great, ran up great, took off, and as soon as the motor warmed up (about two passes, pulled vertical and POP…dead as a rock.  Landed… and the fitting had popped out again.

So I have a few questions…

What caused this to pop out in the first place??

What do I do to put it back in SECURELY

HELP!!!!

-Mark

-----Inline Attachment Follows-----

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.339 / Virus Database: 270.12.40/2135 - Release Date: 06/01/09 17:55:00

-----Inline Attachment Follows-----

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.339 / Virus Database: 270.12.40/2135 - Release Date: 06/01/09 17:55:00

-----Inline Attachment Follows-----

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.5.339 / Virus Database: 270.12.40/2135 - Release Date: 06/01/09 17:55:00

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20090603/41cc43a1/attachment.html>