[NSRCA-discussion] Embarrassing Programming Problem - Inventing the wheel...

[Derek Koopowitz]

He was a pole dancer?

LOL

On Tue, May 6, 2008 at 11:08 AM, Mark Atwood <atwoodm at paragon-inc.com>
wrote:

> For those that want to see Ron in his younger days...  A reenactment.
>
> http://www.youtube.com/watch?v=oTLy6EBmd5s
>
>
> On 5/6/08 1:57 PM, "george w. kennie" <geobet at gis.net> wrote:
>
> > I remember !   What a tough time we had sanding those corners down. If
> only
> > we had thought to balance them.
> > G.
> >
> >
> >
> > ----- Original Message -----
> > From: "Ron Van Putte" <vanputte at cox.net>
> > To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
> > Sent: Monday, May 05, 2008 4:55 PM
> > Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem
> >
> >
> >> I was not around when the wheel was first invented.  However, I
> >> participated in the first post production design iteration:  Making
> >> them round to get rid of the "clunk, clunk, clunk".
> >>
> >> Ron
> >>
> >> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:
> >>
> >>> Because he was around when it was invented the first time???
> >>>
> >>>  :):):):)
> >>>
> >>>
> >>>
> >>>
> >>> On 5/5/08 4:20 PM, "Tony" <tony at radiosouthrc.com> wrote:
> >>>
> >>>> Ron:
> >>>> Why are you re-inventing the wheel?
> >>>> Use the Ailvator pre-set mix for dual elevator servos already
> >>>> built into the
> >>>> 9Z..
> >>>>
> >>>>
> >>>> Tony Stillman, President
> >>>> Radio South, Inc.
> >>>> 139 Altama Connector, Box 322
> >>>> Brunswick, GA  31525
> >>>> 1-800-962-7802
> >>>> www.radiosouthrc.com
> >>>>
> >>>> -----Original Message-----
> >>>> From: nsrca-discussion-bounces at lists.nsrca.org
> >>>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
> >>>> Van Putte
> >>>> Sent: Monday, May 05, 2008 4:09 PM
> >>>> To: General pattern discussion
> >>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
> >>>>
> >>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and using
> >>>> channels 2 and 6 for servos on each elevator half.  I have PMX set
> >>>> for channels 2 and 6, mixing channel 2 into channel 6 and everything
> >>>> works fine, except the servo on channel 6 only moves about 2/3 the
> >>>> throw of the servo on channel 2.  I've tried everything I can think
> >>>> of to rectify the problem with no success.  In addition, there's a
> >>>> small shift in neutral when going from high rate elevator to low
> >>>> rate.
> >>>>
> >>>> I started with an unused model in the menu, so I don't think there's
> >>>> any hidden programming lurking.
> >>>>
> >>>> Any ideas?  I'll be very irritated to find there's a simple solution,
> >>>> but I'd also be very grateful to have the problem go away.
> >>>>
> >>>> Ron Van Putte
> >>>> _______________________________________________
> >>>> NSRCA-discussion mailing list
> >>>> NSRCA-discussion at lists.nsrca.org
> >>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>>>
> >>>> _______________________________________________
> >>>> NSRCA-discussion mailing list
> >>>> NSRCA-discussion at lists.nsrca.org
> >>>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>>
> >>> _______________________________________________
> >>> NSRCA-discussion mailing list
> >>> NSRCA-discussion at lists.nsrca.org
> >>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>
> >> _______________________________________________
> >> NSRCA-discussion mailing list
> >> NSRCA-discussion at lists.nsrca.org
> >> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>
> >
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080506/cc53b51c/attachment.html