<div>He was a pole dancer?</div>
<div> </div>
<div>LOL<br><br></div>
<div class="gmail_quote">On Tue, May 6, 2008 at 11:08 AM, Mark Atwood <<a href="mailto:atwoodm@paragon-inc.com">atwoodm@paragon-inc.com</a>> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">For those that want to see Ron in his younger days... A reenactment.<br><br><a href="http://www.youtube.com/watch?v=oTLy6EBmd5s" target="_blank">http://www.youtube.com/watch?v=oTLy6EBmd5s</a><br>
<br><br>On 5/6/08 1:57 PM, "george w. kennie" <<a href="mailto:geobet@gis.net">geobet@gis.net</a>> wrote:<br><br>> I remember ! What a tough time we had sanding those corners down. If only<br>> we had thought to balance them.<br>
> G.<br>><br>><br>><br>> ----- Original Message -----<br>> From: "Ron Van Putte" <<a href="mailto:vanputte@cox.net">vanputte@cox.net</a>><br>> To: "General pattern discussion" <<a href="mailto:nsrca-discussion@lists.nsrca.org">nsrca-discussion@lists.nsrca.org</a>><br>
> Sent: Monday, May 05, 2008 4:55 PM<br>> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem<br>><br>><br>>> I was not around when the wheel was first invented. However, I<br>>> participated in the first post production design iteration: Making<br>
>> them round to get rid of the "clunk, clunk, clunk".<br>>><br>>> Ron<br>>><br>>> On May 5, 2008, at 3:24 PM, Mark Atwood wrote:<br>>><br>>>> Because he was around when it was invented the first time???<br>
>>><br>>>> :):):):)<br>>>><br>>>><br>>>><br>>>><br>>>> On 5/5/08 4:20 PM, "Tony" <<a href="mailto:tony@radiosouthrc.com">tony@radiosouthrc.com</a>> wrote:<br>
>>><br>>>>> Ron:<br>>>>> Why are you re-inventing the wheel?<br>>>>> Use the Ailvator pre-set mix for dual elevator servos already<br>>>>> built into the<br>>>>> 9Z..<br>
>>>><br>>>>><br>>>>> Tony Stillman, President<br>>>>> Radio South, Inc.<br>>>>> 139 Altama Connector, Box 322<br>>>>> Brunswick, GA 31525<br>>>>> 1-800-962-7802<br>
>>>> <a href="http://www.radiosouthrc.com/" target="_blank">www.radiosouthrc.com</a><br>>>>><br>>>>> -----Original Message-----<br>>>>> From: <a href="mailto:nsrca-discussion-bounces@lists.nsrca.org">nsrca-discussion-bounces@lists.nsrca.org</a><br>
>>>> [mailto:<a href="mailto:nsrca-discussion-bounces@lists.nsrca.org">nsrca-discussion-bounces@lists.nsrca.org</a>] On Behalf Of Ron<br>>>>> Van Putte<br>>>>> Sent: Monday, May 05, 2008 4:09 PM<br>
>>>> To: General pattern discussion<br>>>>> Subject: [NSRCA-discussion] Embarrassing Programming Problem<br>>>>><br>>>>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and using<br>
>>>> channels 2 and 6 for servos on each elevator half. I have PMX set<br>>>>> for channels 2 and 6, mixing channel 2 into channel 6 and everything<br>>>>> works fine, except the servo on channel 6 only moves about 2/3 the<br>
>>>> throw of the servo on channel 2. I've tried everything I can think<br>>>>> of to rectify the problem with no success. In addition, there's a<br>>>>> small shift in neutral when going from high rate elevator to low<br>
>>>> rate.<br>>>>><br>>>>> I started with an unused model in the menu, so I don't think there's<br>>>>> any hidden programming lurking.<br>>>>><br>>>>> Any ideas? I'll be very irritated to find there's a simple solution,<br>
>>>> but I'd also be very grateful to have the problem go away.<br>>>>><br>>>>> Ron Van Putte<br>>>>> _______________________________________________<br>>>>> NSRCA-discussion mailing list<br>
>>>> <a href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a><br>>>>> <a href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target="_blank">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a><br>
>>>><br>>>>> _______________________________________________<br>>>>> NSRCA-discussion mailing list<br>>>>> <a href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a><br>
>>>> <a href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target="_blank">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a><br>>>><br>>>> _______________________________________________<br>
>>> NSRCA-discussion mailing list<br>>>> <a href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a><br>>>> <a href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target="_blank">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a><br>
>><br>>> _______________________________________________<br>>> NSRCA-discussion mailing list<br>>> <a href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a><br>>> <a href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target="_blank">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a><br>
>><br>><br><br>_______________________________________________<br>NSRCA-discussion mailing list<br><a href="mailto:NSRCA-discussion@lists.nsrca.org">NSRCA-discussion@lists.nsrca.org</a><br><a href="http://lists.nsrca.org/mailman/listinfo/nsrca-discussion" target="_blank">http://lists.nsrca.org/mailman/listinfo/nsrca-discussion</a><br>
</blockquote></div><br>