[NSRCA-discussion] Embarrassing Programming Problem

[Jon Lowe]

I had a similar prolem on one o my Jr 10x's.? Had to send it to Horizon and have them?"recalibrate" things.? The elevator rate switch would change trims on a clean setup.


Jon Lowe


-----Original Message-----
From: Troy Newman <troy at troynewman.net>
To: General pattern discussion <nsrca-discussion at lists.nsrca.org>
Sent: Tue, 6 May 2008 2:07 am
Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem



Ron,

I do have some helpful info regarding your trim change with elevator
dual rate. If its not program related....it could be a well worn
elevator gimbal pot.

Tony Stillman can probably speak to this better than...However I did
have it happen many times to me when I was flying my 9Z radios. Radio
South did the fix for me about every 2 years or so. Tony told me the pot
had slipped or was worn...and the "centering" on the sticks was off.
This is why the elevator trim changed with a dual rate flip even though
not conditions or funny trim stuff was happening.

By the way it always happened to the elevator on my radios. I had (2)
9ZAP's and both of them had this problem at various times. I think I
ended up getting the two radios fixed about 2-3 times each...So to me
that was pretty common. Then again I fly too much and wear the stuff
out.

Tony can fix it up in a short order is my guess....or head up to
Pensacola and get Ben to do it for you.


I hope this helps....

I struggled with it and always managed to realize a few days into the
struggle...Oh yea I remember that problem.



Troy Newman

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Verne
Koester
Sent: Monday, May 05, 2008 10:00 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem

Ron,
Are you actually using dual rates within the same flight condition with
the switch or getting the dual rate by going to a different flight
condition? If you're going to a different flight condition, then the
problem could be different trim settings or a different rate of trim on
the second flight condition. It helps to remember that a flight
condition is essentially a whole new model and almost EVERYTHING can be
changed. Your subtrims could be the problem as well. Hope this helps.

Verne


----- Original Message ----- 
From: "Ron Van Putte" <vanputte at cox.net>
To: "General pattern discussion" <nsrca-discussion at lists.nsrca.org>
Sent: Monday, May 05, 2008 5:38 PM
Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem


> OK.  I caved and went with ailevator.  I nulled out the aileron
> inputs and everything works as it should, EXCEPT I'm still getting a
> small neutral shift on both elevators (same direction) when moving
> the elevator dual rate switch.
>
> Ron
>
> On May 5, 2008, at 3:20 PM, Tony wrote:
>
>> Ron:
>> Why are you re-inventing the wheel?
>> Use the Ailvator pre-set mix for dual elevator servos already built
>> into the
>> 9Z..
>>
>>
>> Tony Stillman, President
>> Radio South, Inc.
>> 139 Altama Connector, Box 322
>> Brunswick, GA  31525
>> 1-800-962-7802
>> www.radiosouthrc.com
>>
>> -----Original Message-----
>> From: nsrca-discussion-bounces at lists.nsrca.org
>> [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
>> Van Putte
>> Sent: Monday, May 05, 2008 4:09 PM
>> To: General pattern discussion
>> Subject: [NSRCA-discussion] Embarrassing Programming Problem
>>
>> I'm setting up a new airplane on my Futaba 9ZAP transmitter and using
>> channels 2 and 6 for servos on each elevator half.  I have PMX set
>> for channels 2 and 6, mixing channel 2 into channel 6 and everything
>> works fine, except the servo on channel 6 only moves about 2/3 the
>> throw of the servo on channel 2.  I've tried everything I can think
>> of to rectify the problem with no success.  In addition, there's a
>> small shift in neutral when going from high rate elevator to low
rate.
>>
>> I started with an unused model in the menu, so I don't think there's
>> any hidden programming lurking.
>>
>> Any ideas?  I'll be very irritated to find there's a simple solution,
>> but I'd also be very grateful to have the problem go away.
>>
>> Ron Van Putte
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> 


_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080506/b2a67edf/attachment.html