[NSRCA-discussion] Embarrassing Programming Problem

[brian young]

Theres a way to fix it, mine was doing this, I just cant remember how. There is a guy I know... I bet he will be in touch......
   
  ...is it the trim syncrhonize thingy?....are you using true dual rates I geuss and not a condition?
   
  That radio does a lot but it drives me nuts.

Ron Van Putte <vanputte at cox.net> wrote:
  I might agree, but it does the same thing with two 9Z transmitters. 
I wonder what the odds are that two transmitters have the same problem.

Ron

On May 5, 2008, at 5:15 PM, vicenterc at comcast.net wrote:

> Ron,
>
> I believe that you need to send the radio to Tony for pots 
> adjustment. If the radio is new send it back to Futaba.
>
> --
> Vicente "Vince" Bortone
>
> -------------- Original message --------------
> From: Ron Van Putte 
>
> > OK. I caved and went with ailevator. I nulled out the aileron
> > inputs and everything works as it should, EXCEPT I'm still getting a
> > small neutral shift on both elevators (same direction) when moving
> > the elevator dual rate switch.
> >
> > Ron
> >
> > On May 5, 2008, at 3:20 PM, Tony wrote:
> >
> > > Ron:
> > > Why are you re-inventing the wheel?
> > > Use the Ailvator pre-set mix for dual elevator servos already 
> built
> > > into the
> > > 9Z..
> > >
> > >
> > > Tony Stillman, President
> > > Radio South, Inc.
> > > 139 Altama Connector, Box 322
> > > Brunswick, GA 31525
> > > 1-800-962-7802
> > > www.radiosouthrc.com
> > >
> &g t; > -----Original Message-----
> > > From: nsrca-discussion-bounces at lists.nsrca.org
> > > [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron
> > > Van Putte
> > > Sent: Monday, May 05, 2008 4:09 PM
> > > To: General pattern discussion
> > > Subject: [NSRCA-discussion] Embarrassing Programming Problem
> > >
> > > I'm setting up a new airplane on my Futaba 9ZAP transmitter and 
> using
> > > channels 2 and 6 for servos on each elevator half. I have PMX set
> > > for channels 2 and 6, mixing channel 2 into channel 6 and 
> everything
> > > works fine, except the servo on channel 6 only moves about 2/3 the
> > > throw of the servo on channel 2. I've tried everything I can think
> > > of to rectify the problem with no success. In addition, there's a
> > > small shift in neutral when going from high rate elevator to 
> low rate.
> > >
> > > I st arted with an unused model in the menu, so I don't think 
> there's
> > > any hidden programming lurking.
> > >
> > > Any ideas? I'll be very irritated to find there's a simple 
> solution,
> > > but I'd also be very grateful to have the problem go away.
> > >
> > > Ron Van Putte
> > > _______________________________________________
> > > NSRCA-discussion mailing list
> > > NSRCA-discussion at lists.nsrca.org
> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> > >
> > > _______________________________________________
> > > NSRCA-discussion mailing list
> > > NSRCA-discussion at lists.nsrca.org
> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussio n
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


       
---------------------------------
Be a better friend, newshound, and know-it-all with Yahoo! Mobile.  Try it now.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080505/8a7c3168/attachment.html