[NSRCA-discussion] Embarrassing Programming Problem

[Rex]

Ron
 
Are you using dual rate switches, or conditions and flipping a single switch for multiple surfaces?
If you are using conditions, that seems to be the situation I am describing.  The trims have to be 
active for all conditions, or the trim memory will change for each condition if a trim button is moved
during that condition....  then you switch back to the other condition, and you have a different
trim position.
 
Rex



> From: vanputte at cox.net> Date: Mon, 5 May 2008 17:21:34 -0500> To: nsrca-discussion at lists.nsrca.org> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem> > I might agree, but it does the same thing with two 9Z transmitters. > I wonder what the odds are that two transmitters have the same problem.> > Ron> > On May 5, 2008, at 5:15 PM, vicenterc at comcast.net wrote:> > > Ron,> >> > I believe that you need to send the radio to Tony for pots > > adjustment. If the radio is new send it back to Futaba.> >> > --> > Vicente "Vince" Bortone> >> > -------------- Original message --------------> > From: Ron Van Putte <vanputte at cox.net>> >> > > OK. I caved and went with ailevator. I nulled out the aileron> > > inputs and everything works as it should, EXCEPT I'm still getting a> > > small neutral shift on both elevators (same direction) when moving> > > the elevator dual rate switch.> > >> > > Ron> > >> > > On May 5, 2008, at 3:20 PM, Tony wrote:> > >> > > > Ron:> > > > Why are you re-inventing the wheel?> > > > Use the Ailvator pre-set mix for dual elevator servos already > > built> > > > into the> > > > 9Z..> > > >> > > >> > > > Tony Stillman, President> > > > Radio South, Inc.> > > > 139 Altama Connector, Box 322> > > > Brunswick, GA 31525> > > > > > > > www.radiosouthrc.com> > > >> > &g t; > -----Original Message-----> > > > From: nsrca-discussion-bounces at lists.nsrca.org> > > > [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Ron> > > > Van Putte> > > > Sent: Monday, May 05, 2008 4:09 PM> > > > To: General pattern discussion> > > > Subject: [NSRCA-discussion] Embarrassing Programming Problem> > > >> > > > I'm setting up a new airplane on my Futaba 9ZAP transmitter and > > using> > > > channels 2 and 6 for servos on each elevator half. I have PMX set> > > > for channels 2 and 6, mixing channel 2 into channel 6 and > > everything> > > > works fine, except the servo on channel 6 only moves about 2/3 the> > > > throw of the servo on channel 2. I've tried everything I can think> > > > of to rectify the problem with no success. In addition, there's a> > > > small shift in neutral when going from high rate elevator to > > low rate.> > > >> > > > I st arted with an unused model in the menu, so I don't think > > there's> > > > any hidden programming lurking.> > > >> > > > Any ideas? I'll be very irritated to find there's a simple > > solution,> > > > but I'd also be very grateful to have the problem go away.> > > >> > > > Ron Van Putte> > > > _______________________________________________> > > > NSRCA-discussion mailing list> > > > NSRCA-discussion at lists.nsrca.org> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion> > > >> > > > _______________________________________________> > > > NSRCA-discussion mailing list> > > > NSRCA-discussion at lists.nsrca.org> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion> > >> > > _______________________________________________> > > NSRCA-discussion mailing list> > > NSRCA-discussion at lists.nsrca.org> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussio n> > _______________________________________________> > NSRCA-discussion mailing list> > NSRCA-discussion at lists.nsrca.org> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion> > _______________________________________________> NSRCA-discussion mailing list> NSRCA-discussion at lists.nsrca.org> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080505/8a217681/attachment.html