<html>
<head>
<style>
.hmmessage P
{
margin:0px;
padding:0px
}
body.hmmessage
{
FONT-SIZE: 10pt;
FONT-FAMILY:Tahoma
}
</style>
</head>
<body class='hmmessage'>Ron<BR>
<BR>
Are you using dual rate switches, or conditions and flipping a single switch for multiple surfaces?<BR>
If you are using conditions, that seems to be the situation I am describing. The trims have to be <BR>
active for all conditions, or the trim memory will change for each condition if a trim button is moved<BR>
during that condition.... then you switch back to the other condition, and you have a different<BR>
trim position.<BR>
<BR>
Rex<BR><BR><BR><BR><BR>
<HR id=stopSpelling>
<BR>
> From: vanputte@cox.net<BR>> Date: Mon, 5 May 2008 17:21:34 -0500<BR>> To: nsrca-discussion@lists.nsrca.org<BR>> Subject: Re: [NSRCA-discussion] Embarrassing Programming Problem<BR>> <BR>> I might agree, but it does the same thing with two 9Z transmitters. <BR>> I wonder what the odds are that two transmitters have the same problem.<BR>> <BR>> Ron<BR>> <BR>> On May 5, 2008, at 5:15 PM, vicenterc@comcast.net wrote:<BR>> <BR>> > Ron,<BR>> ><BR>> > I believe that you need to send the radio to Tony for pots <BR>> > adjustment. If the radio is new send it back to Futaba.<BR>> ><BR>> > --<BR>> > Vicente "Vince" Bortone<BR>> ><BR>> > -------------- Original message --------------<BR>> > From: Ron Van Putte <vanputte@cox.net><BR>> ><BR>> > > OK. I caved and went with ailevator. I nulled out the aileron<BR>> > > inputs and everything works as it should, EXCEPT I'm still getting a<BR>> > > small neutral shift on both elevators (same direction) when moving<BR>> > > the elevator dual rate switch.<BR>> > ><BR>> > > Ron<BR>> > ><BR>> > > On May 5, 2008, at 3:20 PM, Tony wrote:<BR>> > ><BR>> > > > Ron:<BR>> > > > Why are you re-inventing the wheel?<BR>> > > > Use the Ailvator pre-set mix for dual elevator servos already <BR>> > built<BR>> > > > into the<BR>> > > > 9Z..<BR>> > > ><BR>> > > ><BR>> > > > Tony Stillman, President<BR>> > > > Radio South, Inc.<BR>> > > > 139 Altama Connector, Box 322<BR>> > > > Brunswick, GA 31525<BR>> > > > <BR>> > > > www.radiosouthrc.com<BR>> > > ><BR>> > &g t; > -----Original Message-----<BR>> > > > From: nsrca-discussion-bounces@lists.nsrca.org<BR>> > > > [mailto:nsrca-discussion-bounces@lists.nsrca.org] On Behalf Of Ron<BR>> > > > Van Putte<BR>> > > > Sent: Monday, May 05, 2008 4:09 PM<BR>> > > > To: General pattern discussion<BR>> > > > Subject: [NSRCA-discussion] Embarrassing Programming Problem<BR>> > > ><BR>> > > > I'm setting up a new airplane on my Futaba 9ZAP transmitter and <BR>> > using<BR>> > > > channels 2 and 6 for servos on each elevator half. I have PMX set<BR>> > > > for channels 2 and 6, mixing channel 2 into channel 6 and <BR>> > everything<BR>> > > > works fine, except the servo on channel 6 only moves about 2/3 the<BR>> > > > throw of the servo on channel 2. I've tried everything I can think<BR>> > > > of to rectify the problem with no success. In addition, there's a<BR>> > > > small shift in neutral when going from high rate elevator to <BR>> > low rate.<BR>> > > ><BR>> > > > I st arted with an unused model in the menu, so I don't think <BR>> > there's<BR>> > > > any hidden programming lurking.<BR>> > > ><BR>> > > > Any ideas? I'll be very irritated to find there's a simple <BR>> > solution,<BR>> > > > but I'd also be very grateful to have the problem go away.<BR>> > > ><BR>> > > > Ron Van Putte<BR>> > > > _______________________________________________<BR>> > > > NSRCA-discussion mailing list<BR>> > > > NSRCA-discussion@lists.nsrca.org<BR>> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion<BR>> > > ><BR>> > > > _______________________________________________<BR>> > > > NSRCA-discussion mailing list<BR>> > > > NSRCA-discussion@lists.nsrca.org<BR>> > > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion<BR>> > ><BR>> > > _______________________________________________<BR>> > > NSRCA-discussion mailing list<BR>> > > NSRCA-discussion@lists.nsrca.org<BR>> > > http://lists.nsrca.org/mailman/listinfo/nsrca-discussio n<BR>> > _______________________________________________<BR>> > NSRCA-discussion mailing list<BR>> > NSRCA-discussion@lists.nsrca.org<BR>> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion<BR>> <BR>> _______________________________________________<BR>> NSRCA-discussion mailing list<BR>> NSRCA-discussion@lists.nsrca.org<BR>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion<BR><BR></body>
</html>