[NSRCA-discussion] O-Ring for Hatori Short Pipe

Mon Jul 14 04:39:06 AKDT 2008

I have about 50 flights on one with no problems.
Probably change it just before I leave for the Nats.
JLK

Date: Mon, 14 Jul 2008 08:14:46 -0400From: jim.woodward at baesystems.comTo: nsrca-discussion at lists.nsrca.orgSubject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

Any reports on this McMaster Carr O-ring?

Thanks,
Jim

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of vicenterc at comcast.netSent: Thursday, June 26, 2008 9:42 PMTo: General pattern discussionSubject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

Good.  Check that O-ring and let us know if works for you.

Thanks,

--Vicente "Vince" Bortone

-------------- Original message -------------- From: John Konneker <jlkonn at hotmail.com> Yes, it's Viton.I got the DVD today.  I had forgotten all about it!!!!Didn't remember it until I opened the envelope.Gettin' old!:-)JLK

From: vicenterc at comcast.netTo: nsrca-discussion at lists.nsrca.orgDate: Fri, 27 Jun 2008 01:29:33 +0000Subject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

John,

Probably is going to work.  It gets so hot that the material expand and could be OK.  Is the material you got Viton?

Thanks,

--Vicente "Vince" Bortone

-------------- Original message -------------- From: John Konneker <jlkonn at hotmail.com> I got the McMaster Carr ones this evening.  They are NOT the same as the originals but they may work.The McMC's are slightly larger ID and OD when compared up against what came with the 821 muffler.But, when you put it in the muffler it compresses it down to the same friction feel as the Hatori.I am going to run it tomorrow and see how it does.Joe Dunnaway has some US dimensioned "O" rings that work.  He will get ahold of a measuring device in the nextday or two and let us know what the measurements are.JLK

From: vicenterc at comcast.netTo: nsrca-discussion at lists.nsrca.orgDate: Fri, 27 Jun 2008 00:56:38 +0000Subject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

That is 15.47 mm ID and 22.53 OD.  It is close to 15 and 22 mm.  Let us know if works in the long run.  

Thanks,

--Vicente "Vince" Bortone

-------------- Original message -------------- From: "Richard Lewis" <humptybump at sbcglobal.net> 

I bought 9464K67 from McMaster

Viton O-Ring, 5/8 x 7/8 (Actual 0.609 I.D. and 0.887 O.D.) 

They are somewhat harder than the original, but the size seems perfect.

I’m using it now, but only have about 10 flights on it.  So far so good, no evidence of leaks at all.  These also fit the MK tailwheel hub nicely..:)

We looked up the metric ones, but I did not think any of the metric dims were close enough…Let us know how the metrics work out for you.

Richard Lewis

From: nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of John KonnekerSent: Thursday, June 26, 2008 2:26 PMTo: General pattern discussionSubject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

I just ordered some of these from McMaster Carr.  I should have them tomorrow.Maybe someone can comment if these are the ones to use.

9263K772 

Metric Viton O-Ring 3.5 mm Width, 16 mm ID, Packs of 10 (Same as 9263K11)

JLK

Date: Thu, 26 Jun 2008 15:03:39 -0400From: atwoodm at paragon-inc.comTo: nsrca-discussion at lists.nsrca.orgSubject: [NSRCA-discussion] O-Ring for Hatori Short Pipe
Can someone direct me to a source (or several) for replacement o-rings to connect the Hatori 821 short pipe to the Hatori 822 header?  Central is out of the authentic Hatori O-rings and won’t have more for a while.  Is there another source, or a suitable replacement available?  Thanks,Mark
No virus found in this incoming message.Checked by AVG.Version: 7.5.524 / Virus Database: 270.4.1/1515 - Release Date: 6/23/2008 7:16 PMNo virus found in this outgoing message.Checked by AVG.Version: 7.5.524 / Virus Database: 270.4.1/1515 - Release Date: 6/23/2008 7:16 PM

--Forwarded Message Attachment--From: humptybump at sbcglobal.netTo: nsrca-discussion at lists.nsrca.orgSubject: Re: [NSRCA-discussion] O-Ring for Hatori Short PipeDate: Fri, 27 Jun 2008 00:32:00 +0000_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

--Forwarded Message Attachment--From: jlkonn at hotmail.comTo: nsrca-discussion at lists.nsrca.orgSubject: Re: [NSRCA-discussion] O-Ring for Hatori Short PipeDate: Fri, 27 Jun 2008 01:25:29 +0000_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080714/ad4a41f2/attachment.html>