[NSRCA-discussion] O-Ring for Hatori Short Pipe

Mon Jul 14 04:17:03 AKDT 2008

Any reports on this McMaster Carr O-ring?

Thanks,

Jim

________________________________

From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of
vicenterc at comcast.net
Sent: Thursday, June 26, 2008 9:42 PM
To: General pattern discussion
Subject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

Good.  Check that O-ring and let us know if works for you.

Thanks,

--
Vicente "Vince" Bortone

	-------------- Original message -------------- 
	From: John Konneker <jlkonn at hotmail.com> 
	Yes, it's Viton.
	I got the DVD today.  I had forgotten all about it!!!!
	Didn't remember it until I opened the envelope.
	Gettin' old!
	:-)
	JLK

________________________________

	From: vicenterc at comcast.net
	To: nsrca-discussion at lists.nsrca.org
	Date: Fri, 27 Jun 2008 01:29:33 +0000
	Subject: Re: [NSRCA-discussion] O-Ring for Hatori Short Pipe

	John,

	Probably is going to work.  It gets so hot that the material
expand and could be OK.  Is the material you got Viton?

	Thanks,

	--
	Vicente "Vince" Bortone

		-------------- Original message -------------- 
		From: John Konneker <jlkonn at hotmail.com> 
		I got the McMaster Carr ones this evening.  They are NOT
the same as the originals but they may work.
		The McMC's are slightly larger ID and OD when compared
up against what came with the 821 muffler.
		But, when you put it in the muffler it compresses it
down to the same friction feel as the Hatori.
		I am going to run it tomorrow and see how it does.
		Joe Dunnaway has some US dimensioned "O" rings that
work.  He will get ahold of a measuring device in the next
		day or two and let us know what the measurements are.
		JLK

________________________________

		From: vicenterc at comcast.net
		To: nsrca-discussion at lists.nsrca.org
		Date: Fri, 27 Jun 2008 00:56:38 +0000
		Subject: Re: [NSRCA-discussion] O-Ring for Hatori Short
Pipe

		That is 15.47 mm ID and 22.53 OD.  It is close to 15 and
22 mm.  Let us know if works in the long run.  

		Thanks,

		--
		Vicente "Vince" Bortone

			-------------- Original message -------------- 
			From: "Richard Lewis" <humptybump at sbcglobal.net>

			I bought 9464K67 from McMaster

			Viton O-Ring, 5/8 x 7/8 (Actual 0.609 I.D. and
0.887 O.D.) 

			They are somewhat harder than the original, but
the size seems perfect.

			I'm using it now, but only have about 10 flights
on it.  So far so good, no evidence of leaks at all.  These also fit the
MK tailwheel hub nicely..:)

			We looked up the metric ones, but I did not
think any of the metric dims were close enough...Let us know how the
metrics work out for you.

			Richard Lewis

________________________________

			From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of John
Konneker
			Sent: Thursday, June 26, 2008 2:26 PM
			To: General pattern discussion
			Subject: Re: [NSRCA-discussion] O-Ring for
Hatori Short Pipe

			I just ordered some of these from McMaster Carr.
I should have them tomorrow.
			Maybe someone can comment if these are the ones
to use.

9263K772
<http://www.mcmaster.com/nav/enter.asp?partnum=9263K772&pagenum=3390>  

Metric Viton O-Ring 3.5 mm Width, 16 mm ID, Packs of 10 (Same as
9263K11)

			JLK

________________________________

			Date: Thu, 26 Jun 2008 15:03:39 -0400
			From: atwoodm at paragon-inc.com
			To: nsrca-discussion at lists.nsrca.org
			Subject: [NSRCA-discussion] O-Ring for Hatori
Short Pipe

			Can someone direct me to a source (or several)
for replacement o-rings to connect the Hatori 821 short pipe to the
Hatori 822 header?  Central is out of the authentic Hatori O-rings and
won't have more for a while.  Is there another source, or a suitable
replacement available?  

			Thanks,

			Mark

			No virus found in this incoming message.
			Checked by AVG.
			Version: 7.5.524 / Virus Database: 270.4.1/1515
- Release Date: 6/23/2008 7:16 PM

			No virus found in this outgoing message.
			Checked by AVG.
			Version: 7.5.524 / Virus Database: 270.4.1/1515
- Release Date: 6/23/2008 7:16 PM

			--Forwarded Message Attachment--
			From: humptybump at sbcglobal.net
			To: nsrca-discussion at lists.nsrca.org
			Subject: Re: [NSRCA-discussion] O-Ring for
Hatori Short Pipe
			Date: Fri, 27 Jun 2008 00:32:00 +0000

			_______________________________________________

			NSRCA-discussion mailing list

			NSRCA-discussion at lists.nsrca.org

http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

		--Forwarded Message Attachment--
		From: jlkonn at hotmail.com
		To: nsrca-discussion at lists.nsrca.org
		Subject: Re: [NSRCA-discussion] O-Ring for Hatori Short
Pipe
		Date: Fri, 27 Jun 2008 01:25:29 +0000

		_______________________________________________

		NSRCA-discussion mailing list

		NSRCA-discussion at lists.nsrca.org

		http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20080714/5db6e9e1/attachment-0001.html>