[NSRCA-discussion] Paint from a can?

wgalligan wgalligan at goodsonacura.com
Thu May 10 09:20:50 AKDT 2007


Yahh.... but that stuff is not nitro tolerant.

WG

  ----- Original Message ----- 
  From: Nat Penton 
  To: NSRCA Mailing List 
  Sent: Thursday, May 10, 2007 11:21 AM
  Subject: Re: [NSRCA-discussion] Paint from a can?


  The Dupli-Color paint from NAPA autoparts is the same manufacturer as Century 21 from Coverite. They have four colors ( or more) of Dupli-Color primer. The nozzles work excellently
    ----- Original Message ----- 
    From: wgalligan 
    To: NSRCA Mailing List 
    Sent: Thursday, May 10, 2007 9:15 AM
    Subject: Re: [NSRCA-discussion] Paint from a can?


    Jim,

    Art Wagner and myself use Lustercoat to paint with.  Art did an article in one of the K-Factor...cant remember which one at the moment.

    Warming the cans in hot water or with a hair dryer is really needed.  Keep a supply of nozzles handy soaking in acetone and change them frequently to avoid splattering from partial clogging.  Make sure your finger tip does not over lap the top of the nozzle.  I have found the over spray can drip off your finger tip into the air stream and make a blob in the spray area.  Art says the new cans of paint seem to be better formulated and have a better spray nozzle.  So be careful of old stock.
    I use the Lustercoat white primer.  Century 21 white for base coat or Lustercote.  Century 21 has the best nozzle on spray can that I have found to date.  Its just hard to match some of the colors to Monocoat. You can color sand Lustercoat and Century 21 and hand polish the sheen back and not have to clearcoat.   Or use PPG clearcoat for a no maintenance type finish.

    Hope this helps.

    Wayne Galligan
      ----- Original Message ----- 
      From: Jim Woodward 
      To: NSRCA Mailing List 
      Sent: Thursday, May 10, 2007 8:43 AM
      Subject: [NSRCA-discussion] Paint from a can?


      Hi Guys,


      I researched the archives but could not find the threads where someone was (I think) describing a paint job from Lustercote, where they warmed the cans prior to painting and the results turned out very good.  Could someone please point me to that thread?


      Thanks,

      Jim W.


      CONFIDENTIALITY NOTICE: This e-mail message, including any attachments, is for the sole use of the intended recipient(s) and may contain confidential and proprietary information.  Any unauthorized review, use, disclosure or distribution is prohibited.  If you are not the intended recipient(s), please contact the sender by reply e-mail and destroy all copies of the original message. 


--------------------------------------------------------------------------


      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20070510/172e9080/attachment.html 


More information about the NSRCA-discussion mailing list