[NSRCA-discussion] Masters 2007 Figure "M" question

[Richard Strickland]

When I'm doing a couple maneuvers after a sequence, many times I'll do an M
with 3/4 rolls.  It's pretty and I still get a buzz when I don't screw it
up.(too badly)

Richard

-----Original Message-----
From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org]On Behalf Of
jivey61 at bellsouth.net
Sent: Tuesday, October 17, 2006 11:54 AM
To: NSRCA Mailing List
Subject: Re: [NSRCA-discussion] Masters 2007 Figure "M" question


Jerry
You are right I looked at the aresti again and the rolls are shown the same
direction.
Sorry Bob...my bad.Gotta get another crutch now.
Jim Ivey
----- Original Message -----
From: "Jerry Budd" <jerry at buddengineering.com>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, October 17, 2006 12:19 PM
Subject: Re: [NSRCA-discussion] Masters 2007 Figure "M" question


> Hi Jim,
>
> Unless the maneuver has changed from 15 years ago all the rolls have
> to be in the same direction, resulting in one stall turn being
> canopy-facing you and the other being belly-facing you (your choice
> as to which comes first).  It's a tough maneuver, especially when the
> wind is blowing other than down the runway.
>
> Jerry
>
>
> >Bob
> >  My memory crutch is,when flying from left to right, the 1st 2 roll
> >directions are left-left and 2nd 2 roll directions are right-right.
> >When flying from the right to left,the 1st 2 roll directions are
right-right
> >and 2nd 2 roll directions are left-left.
> >Like Arch said the center half  loop is inverted in both cases.
> >Lotsa a upside down.
> >
> >Jim Ivey
> >
> >----- Original Message -----
> >From: "Archie Stafford" <rcpattern at stx.rr.com>
> >To: "'NSRCA Mailing List'" <nsrca-discussion at lists.nsrca.org>
> >Sent: Tuesday, October 17, 2006 11:11 AM
> >Subject: Re: [NSRCA-discussion] Masters 2007 Figure "M" question
> >
> >
> >>  Bob,
> >>
> >>  It has to be inverted.  The direction of roll must be the same on
every
> >3/4
> >>  roll therefore you end up inverted across the middle.
> >>
> >>  Arch
> >>
> >>  -----Original Message-----
> >>  From: nsrca-discussion-bounces at lists.nsrca.org
> >>  [mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Bob
Kane
> >>  Sent: Tuesday, October 17, 2006 9:53 AM
> >>  To: nsrca-discussion at lists.nsrca.org
> >>  Subject: [NSRCA-discussion] Masters 2007 Figure "M" question
> >>
> >>  OK, I'm finally try to fly this thing with a pencil . . . . . .    one
> >>  question I have (so far) is the 1/2 loop between the two stall turns
in
> >the
> >>  figure M: Does it matter if it is an inside or outside half loop?  The
> >>  aresti diagram posted on Flying Giants shows it as an outside half
loop
> >with
> >>  no option.  Thanks.
> >>
> >>  Bob Kane
> >>  getterflash at yahoo.com
> >>
> >>
> >>
> >>  _______________________________________________
> >>  NSRCA-discussion mailing list
> >>  NSRCA-discussion at lists.nsrca.org
> >>  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>
> >>  _______________________________________________
> >>  NSRCA-discussion mailing list
> >>  NSRCA-discussion at lists.nsrca.org
> >>  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> >_______________________________________________
> >NSRCA-discussion mailing list
> >NSRCA-discussion at lists.nsrca.org
> >http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>
> --
> ___________
> Jerry Budd
> Budd Engineering
> (661) 722-5669 Voice/Fax
> (661) 435-0358 Cell Phone
> mailto:jerry at buddengineering.com
> http://www.buddengineering.com
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion

_______________________________________________
NSRCA-discussion mailing list
NSRCA-discussion at lists.nsrca.org
http://lists.nsrca.org/mailman/listinfo/nsrca-discussion