[NSRCA-discussion] Sears Thermometer

[Jr LESHER]

Pat
I have the very same thermometer.   It doesn't have an "off" switch.  It shuts off by itself after 10-15 seconds.

Rex Lesher
  ----- Original Message ----- 
  From: vicenterc at comcast.net<mailto:vicenterc at comcast.net> 
  To: NSRCA Mailing List<mailto:nsrca-discussion at lists.nsrca.org> 
  Sent: Sunday, March 05, 2006 8:04 PM
  Subject: Re: [NSRCA-discussion] Sears Thermometer


  Pat,

  Try pressing the on switch for a longer time holding few seconds.  Sometimes, the on switch is also used as off switch doing the described procedure.  I just guessing.  Good luck,

  Vicente

    -------------- Original message -------------- 
    From: "Pat Hewitt" <phewitt at farmersagent.com<mailto:phewitt at farmersagent.com>> 

    > 
    > I have lost my manual for the Sears Thermometer #82327 and I have tried Sears 
    > web with no luck. My problem is the only way I can turn it off is to take the 
    > battery out any body out there have one. 
    > 
    > Pat 
    > 
    > 
    > 
    > ------ Original Message ------ 
    > Received: 07:04 PM CST, 03/05/2006 
    > From: vicenterc at comcast.net 
    > To: NSRCA Mailing List , NSRCA 
    > Mailing List , 
    > nsrca-discussion at lists.nsrca.org 
    > Subject: Re: [NSRCA-discussion] Fuel Regulation in 2C Engines 
    > 
    > I agree 100%. This is a natural big disadvantage of 2 stroke engines. 
    > 
    > Vicente 
    > 
    > --------------! Original message -------------- 
    > From: jeffghughes at comcast.net 
    > 
    > While you may be able to improve the throttle-down in a two stroke, I doubt if 
    > you will be able to match that of a 4 stroke. Two strokes generally run lower 
    > compression ratios and pack the case with fuel. Both make it tough to throttle 
    > down quickly. It's real noticeable in bigger engines like motorcycles. I used 
    > to have a big Kawasaki 750 triple that had almost no off-throttle braking. 
    > Nearly killed myself the first time I drove a honda 750. Backing off the 
    > throttle of a high compression 4 stroke is almost like applying the brakes. 
    > 
    > -------------- Original message -------------- 
    > From: vicenterc at comcast.net 
    > 
    > Good morning all, 
    > 
    > I have been using the OS 160, OS 140 RX and Mintor 140 with good results in 
    > the last 4-5 years. We have been comparing and discussing the adv! antages of 
    > YS compared with 2C. One of the main advantages of YS is that in transition 
    > when power down the engine goes instantly to 2000 RPM or less. The 2C engines 
    > always takes too much time to get down to idle and I believe that causes us 
    > (in pattern) some problems. 
    > 
    > I have been thinking that the problem is that the carburetor and or fuel 
    > system that can not regulate properly (pressure or flow). I think in these 
    > engines, the pumps are set to deliver fuel at full flow (or pressure) without 
    > any regulation system (like the YS). I had the opportunity to discuss this 
    > issue with Perry Pump and they recommended to install a by-pass line. The 
    > idea is to send the excess fuel (pressure) back to the tank during transition. 
    > Perry Pump recommended to install the T as close as possible to the 
    > carburetor needle valve. Also in their web site they have an idea that he 
    > said is used for cars that is a by-pass line that loop around the pu! mp 
    > (http://www.perrypumps.com/instructions.htm, Click on Pump and By-Pass 
    > Systems). I think the ideas deserve some checking since it is natural to have 
    > this type of regulation to maintain constant press! ! ure in the line before 
    > needle valve. I tried the other day the by-pass to the carburetor but I 
    > installed the T ! 
    > too far from the carburetor and forgot to open the vent in the tank. Of 
    > course the results were bad since I was developing vacuum in the tank. I will 
    > try these options of by-pass lines as soon as get warmer. However, I think 
    > someone out there already tried to do this and know results so I am looking 
    > for feed back. 
    > 
    > Thanks in advance, 
    > 
    > Vicente Bortone 
    > 
    > > --------------------------------------------- 
    > > Attachment: Forwarded Message 
    > > MIME Type: message/rfc822 
    > > -------------------------! -------------------- 
    > 
    > 
    > 
    > _____________ __________________________________ 
    > NSRCA-discussion mailing list 
    > NSRCA-discussion at lists.nsrca.org 
    > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 
  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060305/2657d89b/attachment.html