[NSRCA-discussion] Brio Wing Dihedral?

[Anthony Romano]

Sorry, it took me so long but this has been the first time my wings have 
been out of the van! That number seems right. A quick measure of the damaged 
panels from #1 is around an inch. Can't take the servos of of the #2 pair 
but if you turn them over they have slightly more than flat! Go with it 
because I have zero roll mix KE.

Anthony


>From: "Lance Van Nostrand" <patterndude at comcast.net>
>Reply-To: NSRCA Mailing List <nsrca-discussion at lists.nsrca.org>
>To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
>Subject: Re: [NSRCA-discussion] Brio Wing Dihedral?
>Date: Tue, 13 Jun 2006 19:29:34 -0500
>
>When I measure dihedral I do the same as you with the wings on the tube.
>Then I get the wings at 0 degrees incidence to the table (LE and TE same
>height).  Then I measure the difference between the TE at the root and the
>tip.
>
>----- Original Message -----
>From: "Anthony Romano" <anthonyr105 at hotmail.com>
>To: <nsrca-discussion at lists.nsrca.org>
>Sent: Friday, June 09, 2006 2:52 PM
>Subject: Re: [NSRCA-discussion] Brio Wing Dihedral?
>
>
> > Hi Lance,
> > How are you measuring this?
> >
> > Anthony
> >
> >
> >>From: "Lance Van Nostrand" <patterndude at comcast.net>
> >>Reply-To: NSRCA Mailing List <nsrca-discussion at lists.nsrca.org>
> >>To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
> >>Subject: Re: [NSRCA-discussion] Brio Wing Dihedral?
> >>Date: Fri, 9 Jun 2006 07:33:32 -0500
> >>
> >>G,
> >>The Brio wing I am working with is from an unbult kit.  I'm questioning
> >>this too, but the plane's a good flier so if this wing is not messed up
> >>then it is what it is.  The 7/8" I measured is per panel.  I hope to get
> >>confirmation.
> >>
> >>--Lance
> >>
> >>   ----- Original Message -----
> >>   From: george w. kennie
> >>   To: NSRCA Mailing List
> >>   Sent: Thursday, June 08, 2006 11:09 AM
> >>   Subject: Re: [NSRCA-discussion] Brio Wing Dihedral?
> >>
> >>
> >>   That sounds like a lot to me, Lance. Even if that's total (as opposed
> >> to
> >>per panel), it sounds like a candidate for significant proverse roll
> >>couple. The wing would need to be about 3&1/2" below the datum line for
> >>that amount, and I certainly don't think that is the case.
> >>   G.
> >>
> >>
> >>
> >>     ----- Original Message -----
> >>     From: Lance Van Nostrand
> >>     To: NSRCA Mailing List
> >>     Sent: Wednesday, June 07, 2006 10:06 PM
> >>     Subject: [NSRCA-discussion] Brio Wing Dihedral?
> >>
> >>
> >>     I am measuring 7/8" dihedral on Brio wings.  Is this correct?
> >>
> >>
> >>----------------------------------------------------------------------------
> >>
> >>
> >>     _______________________________________________
> >>     NSRCA-discussion mailing list
> >>     NSRCA-discussion at lists.nsrca.org
> >>     http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >>
> >>
> >>------------------------------------------------------------------------------
> >>
> >>
> >>   _______________________________________________
> >>   NSRCA-discussion mailing list
> >>   NSRCA-discussion at lists.nsrca.org
> >>   http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> >
> >>_______________________________________________
> >>NSRCA-discussion mailing list
> >>NSRCA-discussion at lists.nsrca.org
> >>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> >
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>_______________________________________________
>NSRCA-discussion mailing list
>NSRCA-discussion at lists.nsrca.org
>http://lists.nsrca.org/mailman/listinfo/nsrca-discussion