[NSRCA-discussion] Analog Servo RF Masking and....Thanks!

Wed Jul 5 12:54:48 AKDT 2006

Well I think I may have found somthing that works. I put a Futaba PCM
receiver in instead of my PPM receiver, and everything seemes to work. No
buzzing or glitching. However, could the PCM be still masking my problem,
and would there be the potential for lockout? Too much to think about for me
thats for sure. I'll have to do some more extensive testing with the PCM
reciever to see if it's actually going to help.

For now, the Jeskys have offered to let me borrow a complete JR TX/RX/Servo
set up for the NATS. This is going to be my best way to temporarially solve
the problem, and then after the NATS, we will definitely figure out the true
root of this problem. It's too odd to let go. Thanks a bunch to everyone who
offered setups and what not, the Jeskys live close so its much more
feasable.

I really appreciate everyone's input and it has all helped a great deal.
Right now the closest we've gotten is with the PCM reciever. Hopefully that
will solve the problem.

Scott

On 7/5/06, R. LIPRIE <RLIPRIE at centurytel.net> wrote:
>
>  The best servos you could get, would be DIGITAL.
>                                 Matt
>
> ----- Original Message -----
> *From:* Scott Pavlock <f3aflyer7 at gmail.com>
> *To:* K6XYZ at valornet.com ; NSRCA Mailing List<nsrca-discussion at lists.nsrca.org>
> *Sent:* Wednesday, July 05, 2006 11:04 AM
> *Subject:* Re: [NSRCA-discussion] Analog Servo RF Masking and....Thanks!
>
> First, I just want to say thanks a whole bunch to the people who offered
> me equipment as I've gotten some private e-mails also. It really goes to
> show how great people are in this hobby. I am, however, going to go through
> local sources for different equipment. There are a lot of people at my club
> with plenty of different TX's and RX's in all different brands so instead of
> trying to rush and get things here so quickly, I would rather get them
> locally first. Thanks a ton!!
>
> Next, I want to reiterate my set up because I think this is getting a
> little confusing.
>
> My current set up which shows NO visible problems is:
> -Futaba 9C with the syntheszed module.
> -Hitec Super Slim RX on channel 49.
> -2 Futaba 3010's.
> -2 Hitec HS77's.
> -1 Hitec HS81MG.
> -Duralite 2s2p RX Battery
> -MPI 5.6v Regulator.
> -MPI HD Switch Harness.
> -Cermark gold plated extentions.
>
> Now here is my problem set up which shows the glitch:
> -2 JR 9411sa's
> -1 JR 8417
> -1 JR 8411sa
> -1 JR 3421sa
> -The rest is identical.
>
> As you can see, the only thing that seems to make it work is the alanog
> servos.
>
> Del, they glitch when they are connected and disconnected from the
> surfaces. More so when they are connected, but I can totally rule out the
> airframe being the problem. These servos have at least 2 years of flying on
> them and one of the hypothesis I had was that after being vibrated around
> for 2 years, theyre now feeling like they should always be doing that, even
> without a load. Not sure if that's possible, but I'm just throwin out ideas.
>
>
> The next thing I am going to test is a Futaba PCM receiver on both set
> ups. The set up that works will be in the aircraft, and the set up that
> doesnt will be sitting in the foam transmitter box.
>
> ***Important***
> Yesterday I range tested both set ups. The one that "works" is in the
> plane, and the one that doesnt (JR digitals) was in the transmitter box.
> Both tests were done outside on grass. I put the antenna all the way down
> and walked at least 300 feet with no noticible problem at all when testing
> the airplane. When testing the digital servos, I was able to walk about 100
> feet from the box they were sitting in and thats when they became very
> noticible glitches. This was both with the antenna at 1 section out, and all
> the way up. The glitch was reduced when it was all the way out but it was
> still prevalent.
>
> On 7/5/06, Dave Harmon <K6XYZ at valornet.com> wrote:
> >
> >   Which model Futaba rx is it?
> >
> >
> >
> > Regards
> >
> > Dave Harmon
> > NSRCA 586
> > K6XYZ[at]valornet[dot]com
> > Broken Arrow, Ok.
> >
> > -----Original Message-----
> > *From:* nsrca-discussion-bounces at lists.nsrca.org [mailto:
> > nsrca-discussion-bounces at lists.nsrca.org] *On Behalf Of *John Ferrell
> > *Sent:* Wednesday, July 05, 2006 9:21 AM
> > *To:* NSRCA Mailing List
> > *Subject:* Re: [NSRCA-discussion] Analog Servo RF Masking and....Thanks!
> >
> >
> >
> > I have seen this kind of "Twilight Zone" ( I really like that term!)
> > failure in industrial products. The problem is probably present in the
> > Analog setup but the system is not fast enough for it to show.
> >
> >
> >
> > If the digital servos are trying to latch up on the leading edge of a
> > signal shift they may simply be following switching transients.
> >
> >
> >
> > I seem to recall a condition where Jr had a filter across the signal at
> > the reciever and Futaba had a filter across the signal at the servo. Since
> > it always seemed to work OK  so the condition was ignored. May be that the
> > filter has become essential. I suppose that we may have reached the point in
> > time that we can no longer ignore the differences in the two systems.
> >
> >
> >
> > I have used mixed systems but I have never been comfortable ignoring any
> > engineer's specfications.
> >
> >
> >
> > When you mix the two systems it is a hack and you become the test
> > pilot...
> >
> >
> >
> > BTW, my guess is that the glitch can be fixed with a capacitor (100pf?)
> > across the signal at the servo end. But then it might just make it worse!
> >
> >
> >
> > John Ferrell    W8CCW
> > "My Competition is not my enemy"
> > http://DixieNC.US
> >
> >  ----- Original Message -----
> >
> > *From:* John Pavlick <jpavlick at idseng.com>
> >
> > *To:* NSRCA Mailing List <nsrca-discussion at lists.nsrca.org>
> >
> > *Sent:* Tuesday, July 04, 2006 7:07 PM
> >
> > *Subject:* Re: [NSRCA-discussion] Analog Servo RF Masking and....Thanks!
> >
> >
> >
> > Scott A.: Yeah, a possibility - but he says it works OK with the analog
> > servos. It would be worth checking, but if he has another Rx he could just
> > substitute that (probably already did) and see if the problem goes away.
> > Scott P.: Does moving the antenna change anything? You have to find the
> > common denominator. If it's not the Rx then maybe it has something to do
> > with the installation. There is something going on there and I'm not sure
> > why the digital servos make it more apparent. Find someone who knows how to
> > use a 'scope and see if they can help you. This is weird - you guys have the
> > same first name and my last name looks like yours. Maybe we're all stuck in
> > the Twilight Zone...
> >
> >
> >
> > John Pavlick
> > http://www.idseng.com
> >
> >
> > -----Original Message-----
> > *From:* nsrca-discussion-bounces at lists.nsrca.org [mailto:nsrca-discussion-bounces at lists.nsrca.org
> > ]*On Behalf Of *Scott Anderson
> > *Sent:* Tuesday, July 04, 2006 6:47 PM
> > *To:* NSRCA Mailing List
> > *Subject:* Re: [NSRCA-discussion] Analog Servo RF Masking and....Thanks!
> >
> > Hi Scott,
> >
> >
> >
> > Stupid question, did you send RX out and have it put on a shaker table
> > and checked.. I had a RX issue for over a month and spent time with Tony S.
> > and he found a bad filter on the board..
> >
> >
> >
> > Just my 2 cents from a fellow team member..
> >
> >
> >
> > Scott Anderson
> >
> >  ----- Original Message -----
> >
> > *From:* Scott Pavlock <f3aflyer7 at gmail.com>
> >
> > *To:* NSRCA Mailing List <nsrca-discussion at lists.nsrca.org>
> >
> > *Sent:* Tuesday, July 04, 2006 6:29 PM
> >
> > *Subject:* Re: [NSRCA-discussion] Analog Servo RF Masking and....Thanks!
> >
> >
> >
> > I've used multiple battery set ups including ones without a regulator on
> > a normal NiCd pack, and also on both a 5.6v regulator and a 6v
> > regulator.
> >
> > John,
> >
> > No I don't. I actually have no clue what that is haha.
> >
> > /nsrca-discussion
> >
> >  ------------------------------
> >
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> >
> > _______________________________________________
> > NSRCA-discussion mailing list
> > NSRCA-discussion at lists.nsrca.org
> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
> >
> >
>  ------------------------------
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> ------------------------------
>
> No virus found in this incoming message.
> Checked by AVG Free Edition.
> Version: 7.1.394 / Virus Database: 268.9.8/381 - Release Date: 7/3/2006
>
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060705/ffc74918/attachment-0001.html 