[NSRCA-discussion] Airplane Rack

[Bill Glaze]

Jim:
Thanks, obviously your visualization qualities far surpass my own!<G>  Still 
hoping to see Jerry at Muncie.  I assume that, once again, you will also be 
there?  Bill Glaze
----- Original Message ----- 
From: <jivey61 at bellsouth.net>
To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
Sent: Tuesday, February 28, 2006 9:55 AM
Subject: Re: [NSRCA-discussion] Airplane Rack


> Bill
> The way I see it.!!!! Jerry has 2 square pieces of wood on either side 
> going
> for and aft. They are supported to the floor with 2 square pieces with
> rubber feet,lashed down with bongee cords on either side at the vehicle
> cargo tiedowns at the rear. The rear has a angle(maybe unistrut) turned
> point down and insulated with foam??.... so that the wheels sit in the
> "V".This is where the wing nut attaches the angle to the square wood going
> for and aft.
> The only thing I don't see is... what does the tail of the airplane sit 
> on?
> This arrangement also appears to be for electrics because I don't see any
> protection for the seat material from dripping mufflers etc. I can
> understand this knowing what Jerry flys.
> It is simple and easy.
>
> Jim Ivey
> ----- Original Message ----- 
> From: "Bill Glaze" <billglaze at triad.rr.com>
> To: "NSRCA Mailing List" <nsrca-discussion at lists.nsrca.org>
> Sent: Tuesday, February 28, 2006 9:10 AM
> Subject: Re: [NSRCA-discussion] Airplane Rack
>
>
>> Jerry:
>> Will you have this setup at Muncie this year?  to be honest, I have
> trouble
>> visualizing just what's happening from the photos.  (I don't know why I'm
>> having the trouble; I'm sure the photos make everything clear for all the
>> other folks.)
>> Bill Glaze
>> ----- Original Message ----- 
>> From: "Jerry Budd" <jerry at buddengineering.com>
>> To: <nsrca-discussion at lists.nsrca.org>; <dist7 at nsrca.org>
>> Sent: Tuesday, February 28, 2006 1:15 AM
>> Subject: [NSRCA-discussion] Airplane Rack
>>
>>
>> > Hi all,
>> >
>> > Someone recently asked me to post some photos of the airplane rack I
>> > built for my 2004 Honda Odyssey a couple of years ago.  It holds two
>> > 2m pattern planes and allows for full unrestricted access to the open
>> > storage area underneath it.  It only took an evening to design and
>> > build and it cost ~$25.  It also disassembles very quickly (simply
>> > remove two wing nuts holding down the metal landing gear support) for
>> > those rare occasions when you need to use the mini-van for something
>> > other than storing & transporting your planes!
>> >
>> > Here's a link to some photos:  http://tinyurl.com/s6ncr
>> >
>> > Thx, Jerry
>> > -- 
>> > ___________
>> > Jerry Budd
>> > Budd Engineering
>> > (661) 722-5669 Voice/Fax
>> > (661) 435-0358 Cell Phone
>> > mailto:jerry at buddengineering.com
>> > http://www.buddengineering.com
>> > _______________________________________________
>> > NSRCA-discussion mailing list
>> > NSRCA-discussion at lists.nsrca.org
>> > http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>> >
>>
>>
>> _______________________________________________
>> NSRCA-discussion mailing list
>> NSRCA-discussion at lists.nsrca.org
>> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>
> _______________________________________________
> NSRCA-discussion mailing list
> NSRCA-discussion at lists.nsrca.org
> http://lists.nsrca.org/mailman/listinfo/nsrca-discussion
>