[NSRCA-discussion] YS 160 help needed

[Steve Ford]

Thanks Earl, that's it.  On the phone first thing in the morning.
Thanks,
Steve
  ----- Original Message ----- 
  From: Earl Haury 
  To: NSRCA Mailing List 
  Sent: Wednesday, August 09, 2006 9:11 PM
  Subject: Re: [NSRCA-discussion] YS 160 help needed


  If it's the brass part that is pressed into the head that the check valve is pressed onto - that's the injection nozzle / fitting and it's pressed into the head - shouldn't come out. Time to give Richard a call at YS Service.

  Earl
    ----- Original Message ----- 
    From: Steve Ford 
    To: NSRCA Mailing List 
    Sent: Wednesday, August 09, 2006 9:02 PM
    Subject: Re: [NSRCA-discussion] YS 160 help needed


    I thought it would have been threaded, but it is smooth.  
    Steve
      ----- Original Message ----- 
      From: jivey61 at bellsouth.net 
      To: NSRCA Mailing List 
      Sent: Wednesday, August 09, 2006 8:54 PM
      Subject: Re: [NSRCA-discussion] YS 160 help needed


      Steve
      Doesn't that screw into the head.

      Jim Ivey
        ----- Original Message ----- 
        From: Steve Ford 
        To: NSRCA Mailing List 
        Sent: Wednesday, August 09, 2006 9:33 PM
        Subject: Re: [NSRCA-discussion] YS 160 help needed


        Hi Robert.   The check valve assembly didn't come apart, it was the bottom of it that goes down into the motor that came out.  I may not be describing it correctly, i'm a little mechanically challenged. :))

        Thanks,
        Steve
          ----- Original Message ----- 
          From: Robert & Casey Green 
          To: NSRCA Mailing List 
          Sent: Wednesday, August 09, 2006 8:25 PM
          Subject: Re: [NSRCA-discussion] YS 160 help needed


          Steve see if you can use a fuel tubing to connect the two together
            ----- Original Message ----- 
            From: Steve Ford 
            To: NSRCS Board 
            Sent: Wednesday, August 09, 2006 8:20 PM
            Subject: [NSRCA-discussion] YS 160 help needed


            Hi all.  Tonight on my YS 1.60 the check valve came out of the head of the motor.  It appears to be just a pressure fitting, pushed it back in, but wouldn't stay in.

            Any help would be greatly appreciated, contest this weekend of course.  My thoughts are leaning towards jb weld or something similar.  

            Thanks,
            Steve Ford


--------------------------------------------------------------------


            _______________________________________________
            NSRCA-discussion mailing list
            NSRCA-discussion at lists.nsrca.org
            http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


----------------------------------------------------------------------


          _______________________________________________
          NSRCA-discussion mailing list
          NSRCA-discussion at lists.nsrca.org
          http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


----------------------------------------------------------------------


          No virus found in this incoming message.
          Checked by AVG Free Edition.
          Version: 7.1.394 / Virus Database: 268.10.8/415 - Release Date: 8/9/2006



------------------------------------------------------------------------


        _______________________________________________
        NSRCA-discussion mailing list
        NSRCA-discussion at lists.nsrca.org
        http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


--------------------------------------------------------------------------


      _______________________________________________
      NSRCA-discussion mailing list
      NSRCA-discussion at lists.nsrca.org
      http://lists.nsrca.org/mailman/listinfo/nsrca-discussion 


--------------------------------------------------------------------------


      No virus found in this incoming message.
      Checked by AVG Free Edition.
      Version: 7.1.394 / Virus Database: 268.10.8/415 - Release Date: 8/9/2006



----------------------------------------------------------------------------


    _______________________________________________
    NSRCA-discussion mailing list
    NSRCA-discussion at lists.nsrca.org
    http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


------------------------------------------------------------------------------


  _______________________________________________
  NSRCA-discussion mailing list
  NSRCA-discussion at lists.nsrca.org
  http://lists.nsrca.org/mailman/listinfo/nsrca-discussion


------------------------------------------------------------------------------


  No virus found in this incoming message.
  Checked by AVG Free Edition.
  Version: 7.1.394 / Virus Database: 268.10.8/415 - Release Date: 8/9/2006
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060810/14bca79a/attachment.html