[NSRCA-discussion] Hatori 821

[Derek Koopowitz]

I'm using the Asano header - see attached pictures.  Absolutely no problems
with the header coming loose or the pipe leaking.  Ok, I say no leaking now
but when I first put the pipe in I did not mount the Nishioka legs close
enough so they "popped" out and the pipe did leak.  I also broke off the
honeycomb and that caused the pipe to come loose as well.
 
Very good system and I'm sure the Hatori header will work just fine.
 

  _____  

From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Glen Watson
Sent: Tuesday, April 18, 2006 7:22 PM
To: 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] Hatori 821



Thanks Derek, the decisions you provided is what I was interested in
knowing.  At 24mm, nearly an inch it appears not feasible to use the NMP
header with a traditional Teflon connector.  It would seem the best solution
is to use the Hatori header the muffler was designed to work with such as
the 822.  I assume you are using a Hatori header yourself.   How is the
combination working for you?  Is it leak free?  Is it maintenance free?  Any
special considerations when installing?

 

Thanks,

 

Glen

 

  _____  

From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Derek
Koopowitz
Sent: Tuesday, April 18, 2006 6:33 PM
To: 'NSRCA Mailing List'
Subject: Re: [NSRCA-discussion] Hatori 821

 

I'm using the pipe... when you say OD - are you refering to the total
outside diameter of the actual pipe itself?

 

There are 2 sizes - 24mm is the largest and 21mm is the next size down.
You'll see from your pic that the left most side of the pipe has 2 sizes.  I
just gave you both.

 

  _____  

From: nsrca-discussion-bounces at lists.nsrca.org
[mailto:nsrca-discussion-bounces at lists.nsrca.org] On Behalf Of Glen Watson
Sent: Tuesday, April 18, 2006 1:52 PM
To: 'NSRCA Mailing List'
Subject: [NSRCA-discussion] Hatori 821

Does anyone know the OD of the inlet on the Hatori 821 muffler?  In addition
I would like to know if anyone has used this muffler with a NMP (Central YS
header)?  If so what ID size tubing (Teflon) did you use to make the
connection between the two?

 

Pic of Hatori attached..

 

Thanks in advance

 

Glen Watson

http://www.geocities.com/rcprecision/pah.html

 

 

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060419/08b37198/attachment.html 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: DSC02027.JPG
Type: image/jpeg
Size: 28670 bytes
Desc: not available
Url : http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060419/08b37198/attachment.jpe 
-------------- next part --------------
A non-text attachment was scrubbed...
Name: DSC02028.JPG
Type: image/jpeg
Size: 22620 bytes
Desc: not available
Url : http://lists.nsrca.org/pipermail/nsrca-discussion/attachments/20060419/08b37198/attachment-0001.jpe