: ES spinner

[Anthony Romano]

Has anyone else tried one of these? Will they hold up to a starter?

Anthony

>From: <brianyemail-nsrca at yahoo.com>
>Reply-To: brianyemail-nsrca at yahoo.com
>To: Anthony Romano <anthonyr105 at hotmail.com>
>Subject: Re: ES spinner
>Date: Sun, 13 Mar 2005 14:37:06 -0800 (PST)
>
>I noticed on mine that the weave starts to show where
>the starter runs. I only started the engine a few
>times with it, so I cant say for sure. You will have
>to cut your own prop slots on it too, I made a
>template for mine I can send you a PDF file of it if
>you decide to try it.
>
>I will use it on my 2-stroke but need to drill out the
>prop shaft hole a little.
>
>Brian
>
>
>--- Anthony Romano <anthonyr105 at hotmail.com> wrote:
> >
> > Will this hold up to a starter? It would be on a two
> > cycle so only the first
> > start of the day and the run out require a starter.
> >
> > Anthony
> >
> >
> > >From: <brianyemail-nsrca at yahoo.com>
> > >Reply-To: brianyemail-nsrca at yahoo.com
> > >To: discussion at nsrca.org
> > >Subject: RE: Spinner poll
> > >Date: Sat, 12 Mar 2005 08:08:13 -0800 (PST)
> > >
> > >3-5/8 or 92 mm is a better fit for the Impact or
> > >Abbra.
> > >
> > >ES Composites has a 92mm but the backplate isnt
> > >knurled so it slips on a YS, but it fits the Impact
> > >very well.
> > >
> > >--- Derek Koopowitz <derekkoopowitz at earthlink.net>
> > >wrote:
> > > > A size that is available and fits... ;)
> > > >
> > > > (unlike the 3.5" that isn't around for the
> > Impact)
> > > >
> > > > -----Original Message-----
> > > > From: discussion-request at nsrca.org
> > > > [mailto:discussion-request at nsrca.org] On
> > > > Behalf Of adriancwong at earthlink.net
> > > > Sent: Friday, March 11, 2005 10:17 PM
> > > > To: discussion at nsrca.org
> > > > Subject: Re: Spinner poll
> > > >
> > > > 3-1/4" to 3-3/8"
> > > >
> > > > Adrian
> > > >
> > > >
> > > > -----Original Message-----
> > > > From: Jason <jasonshulman at cox.net>
> > > > Sent: Mar 11, 2005 10:15 PM
> > > > To: NSRCA <discussion at nsrca.org>
> > > > Subject: Spinner poll
> > > >
> > > > What size do you guys like on your 2M planes?
> > > >
> > > > 3"
> > > > 3.25"
> > > > 3.5"
> > > >
> > > > Jason
> > > > www.jasonshulman.com
> > > >
> > > >
> > =================================================
> > > > To access the email archives for this list, go
> > to
> > > > http://lists.f3a.us/pipermail/nsrca-discussion/
> > > > To be removed from this list, go to
> > > > http://www.nsrca.org/discussionA.htm
> > > > and follow the instructions.
> > > >
> > > >
> > > >
> > =================================================
> > > > To access the email archives for this list, go
> > to
> > > > http://lists.f3a.us/pipermail/nsrca-discussion/
> > > > To be removed from this list, go to
> > > > http://www.nsrca.org/discussionA.htm
> > > > and follow the instructions.
> > > >
> > > >
> > > >
> > > >
> > =================================================
> > > > To access the email archives for this list, go
> > to
> > > > http://lists.f3a.us/pipermail/nsrca-discussion/
> > > > To be removed from this list, go to
> > > > http://www.nsrca.org/discussionA.htm
> > > > and follow the instructions.
> > > >
> > > >
> > >=================================================
> > >To access the email archives for this list, go to
> > >http://lists.f3a.us/pipermail/nsrca-discussion/
> > >To be removed from this list, go to
> > http://www.nsrca.org/discussionA.htm
> > >and follow the instructions.
> > >
> >
> >
> >


=================================================
To access the email archives for this list, go to
http://lists.f3a.us/pipermail/nsrca-discussion/
To be removed from this list, go to http://www.nsrca.org/discussionA.htm
and follow the instructions.