[SPAM] Re: Three blade size

[Mike Hester]

I ran that one too, it was quiet, but fast and loaded the engine up too much. Repitched to 12 it'd be about right.

-Mike
  ----- Original Message ----- 
  From: wgalligan 
  To: discussion at nsrca.org 
  Sent: Saturday, June 11, 2005 2:12 AM
  Subject: [SPAM] Re: Three blade size


  I dont think it would be enough load for that much engine.
  I would think a 15.75x13 APC 3 blade would load the OS 1.60 better. 

  WG

    ----- Original Message ----- 
    From: Mike Hester 
    To: discussion at nsrca.org 
    Sent: Friday, June 10, 2005 7:00 PM
    Subject: Re: Three blade size


    The Mejlik 16x11 was AWESOME on the 160fx, best prop by far. Just a bit loud. I think I'll try one of these Cleveland 16x11s and see what the difference is.

    -Mike
      ----- Original Message ----- 
      From: Mark Hunt 
      To: discussion at nsrca.org 
      Sent: Friday, June 10, 2005 7:37 PM
      Subject: Re: Three blade size


      That is notable....3 blades instead of two and yet one ounce lighter than the apc!

      Sounds like a good prop for the 160fx??

      Mark
        ----- Original Message ----- 
        From: Wayne Galligan 
        To: discussion at nsrca.org 
        Sent: Friday, June 10, 2005 3:53 PM
        Subject: Re: Three blade size


        Something different.   Look like clones.    But I think for less $$
        This 16x11 3 blade has good performance and is noticeably slower then the 17x12 2-blade APC.   
        The 3 blade 16x11 is one ounce lighter then the 17x12 APC also.

        Wayne G


          ----- Original Message ----- 
          From: Mike Hester 
          To: discussion at nsrca.org 
          Sent: Friday, June 10, 2005 3:45 PM
          Subject: Re: Three blade size


          Those look a LOT like Mejlik props, wierdly enough even the sizing is the same. What's up with that?

          Anyway I have a Mejlik 16x11 I tested yesterday. It has an extremely wide blade root and a 120 cut  TT was too small to fit. Also the hole Dia is 3/8 so a bushing would need to be used on a 140. I can say this...it's louder than the APC, but it's PERFECT in performance.

          So are these Mejlik clones or are they something different?

          -Mike
            ----- Original Message ----- 
            From: Wayne Galligan 
            To: discussion at nsrca.org 
            Sent: Friday, June 10, 2005 4:06 PM
            Subject: Re: Three blade size


            Cleveland props does make a c.fiber 16x11  and I am using one on my OS 1.40 and I like it.

            see this link:

            http://pages.prodigy.net/gcleveland_grsmodels/_import/pages.prodigy.net/gcleveland_grsmodels/index6.html

            Wayne Galligan
              ----- Original Message ----- 
              From: randy10926 at comcast.net 
              To: discussion at nsrca.org 
              Sent: Friday, June 10, 2005 3:01 PM
              Subject: Re: Three blade size


              I wish they made a 3 blade 16X11

                -------------- Original message -------------- 

                Does anyone make a three blade 16 x 10 ?

                Bob Pastorello
                www.rcaerobats.net
                rcaerobob at cox.net
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.f3a.us/pipermail/nsrca-discussion/attachments/20050611/6568a8c6/attachment.html